NEFF T29DA69N0 Notice D'installation page 11

Gas connection R 1/2
Fit the seal and the connecting piece R 1/2 to the
▶
gas connection on the appliance.
→ Fig.
9
Gas connection G 1/2
Insert the seal between the gas connection of the
▶
appliance and the gas supply.
→ Fig.
10
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
11
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Economy burner
Standard-output burner
High-output burner
Dual-wok multi-crown burner
¡ 1 - Outer flame
¡ 2 - Inner flame
Tools
Contact technical customer service to purchase the
relevant tools.
Removal lever
Removing the cover
Remove the pan supports, burner caps, distribut-
1.
ors and rotary knobs.
Undo the screws on the burners.
2.
If required, place the removal lever on the marked
3.
areas and loosen the front clip fastener.
→ Fig.
12
Carefully remove the cover.
4.
Removing the circuit board
Tip: The circuit board is secured to the holder by
fastening pins at the sides and in the middle. Push
the fastening pins carefully without damaging them.
If one of the pins breaks, the entire holder must be
replaced.
ATTENTION!
The circuit board can be damaged by improper
handling.
Handle the circuit board carefully.
▶
Use anti-static shields or hold the circuit board at
▶
the edges.
Never touch the surfaces of the circuit board on
▶
which there are components or conducting tracks.
1.
2.
3.
→ Fig.
Adjusting the taps
Requirement: The upper part of the appliance and
the circuit board are removed. → "Removing the
cover", Page 11 → "Removing the circuit board",
Page 11
1.
2.
Replacing the nozzles
▶
Reinstalling the appliance
▶
shows the
20
Checking if equipment is working
1.
2.
Documenting the gas type conversion
▶
Calibrating the electronics
483196
▶
Montaje seguro
Tener en cuenta estas indicaciones de seguridad al
montar el aparato.
¡ Lea atentamente estas instrucciones.
¡ Las imágenes representadas en estas instruccio-
¡ Solamente un montaje profesional conforme a las
Un escape de gas puede provocar una explosión.
▶
Undo the fastening pins on one side.
Release the fastening pins in the middle by press-
ing on them from both sides with your fingers.
Undo the fastening pins on the other side and re-
move the circuit board.
13
Remove the cylindrical parts and springs from the
fittings spindle.
When adjusting the bypass screws (M), refer to
the table → Fig. .
20
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
14
Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→ Fig. , → Fig.
15 16
Ensure that the nozzle does not become detached
during removal or fastening.
Install the appliance components in reverse order.
Check that turning the rotary knob between the
position for maximum power and the position for
minimum power does not cause the burner to go
out or result in backfire.
If the gas flow from the burner is not correct, in
the table → Fig. , check whether the nozzle and
20
the position of the bypass screw are correct.
Attach the sticker showing the new gas type near
to the rating plate.
→ Fig. , → Fig. , → Fig.
17 18
Always recalibrate the electronics after reas-
sembling.
es
nes tienen carácter orientativo.
instrucciones de montaje puede garantizar un uso
seguro del aparato. El instalador es responsable
del funcionamiento perfecto en el lugar de instala-
ción.
ADVERTENCIA ‒ Riesgo de explosión!
Todos los trabajos de instalación, conexión, regu-
lación y adaptación a otro tipo de gas deben ser
realizados por un técnico especialista autorizado y
de conformidad con los reglamentos y disposicio-
nes legales vigentes y los reglamentos de las
compañías locales suministradoras de electrici-
19
11