Publicité
Les langues disponibles
Les langues disponibles
EngLIsh
Fitting the Side Handle (Fig. A)
The side handle
5
can be fitted to suit both RH- and LH-users.
WARNING: Always use the drill with the side handle
properly assembled.
1. Loosen the side handle.
-
For RH-users, slide the side handle clamp over the collar
behind the chuck, handle at the left.
-
For LH-users, slide the side handle clamp over the colar
behind the chuck, handle at the right.
2. Rotate the side handle to the desired position and tighten
the handle.
Setting the Drilling Depth (Fig. B)
1. Insert the required drill bit into the chuck.
2. Slacken the side handle
3. Fit the depth adjustment rod
handle clamp.
4. Adjust the drilling depth as shown.
5. Tighten the side handle.
Forward/Reverse Slider (Fig. A)
To select forward or reverse rotation, use the forward/reverse-
switch
3
(see arrow on tool).
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
Two Gear Selector (Fig. D)
Your tool is fitted with a two gear selector
torque ratio.
Release the variable speed switch and select the required
position. This can be done either with the tool switched off or
running under no load condition. Always align the selector with
the arrow on the gear housing:
•
low speed/high torque
(drilling large holes, driving large screws)
•
high speed/low torque
(drilling smaller holes, drilling in wood)
For speed rates, refer to the Technical Data.
Do not change gears at full speed or during use.
Chuck Removal (Fig. E, F)
1. Open the chuck jaws as far as possible.
2. Insert a screwdriver into the chuck and remove the chuck
retaining screw
by turning clockwise.
10
3. Tighten a hex key into the chuck and strike it with a hammer
as shown.
Prior to Operation
•
Insert the appropriate bit.
•
Mark the spot where the hole is to be drilled.
18
5
.
through the hole in the side
6
4
to vary the speed/
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. C)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the main handle
Switching On and Off (Fig. A)
•
To run the tool, press the variable speed switch
pressure exerted on the variable speed switch determines
the tool speed.
If necessary, press the lock-on button
-
operation and release the switch. The lock-on button
works only in full speed, forward rotation.
•
To stop the tool, release the switch.
-
To stop the tool in continuous operation, press the
switch briefly and release it. Always switch off the tool
when work is finished and before unplugging.
Rotary Drilling (Fig. A)
•
Press the switch
.
1
Screwdriving
•
Select forward or reverse rotation.
•
Press the switch
1
.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
5
,
.
9
1
. The
for continuous
2
Publicité
