DeWalt DWP849X Traduction De La Notice D'instructions Originale page 26

EngLIsh
To Attach Polishing Pad with Rubber Backing
Pad (Fig. C1)
1. Engage the hexagonal hole in the backing pad
the clamp washer
14
place the assembly on the tool spindle
2. Hold the spindle lock button
pad and clamp washer clockwise to thread them completely
on the spindle. Tighten firmly by hand.
3. Fix the polishing pad 13
To Attach Polishing Pad with Hook and Loop
Backing Pad (Fig. C2)
1. Attach hook and loop foam or wool pad
loop backing pad 17 , being careful to center the backing
pad with the foam or wool pad.
2. Screw backing pad 17
spindle lock button 4 .
To Remove Pads
Turn the pads by hand in the opposite direction from normal
rotation to allow lock button to engage spindle, then unscrew
pads in normal direction for right-hand thread.
Prior to Operation
1. Be sure the polishing pad is mounted correctly.
2. Make sure the pad rotates in the direction of the arrows on
the accessory and the tool.
3. Make sure any dirt is washed off the workpiece surface.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from
power source before making any adjustments or
removing/installing attachments or accessories.
Before reconnecting the tool, depress and release the
trigger switch to ensure that the tool is off.

WARNING:
• Apply only a gentle pressure to the tool. Do not exert
side pressure on the backing pad.
• Avoid overloading. Should the tool become hot, let it
run a few minutes under no load condition.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
the bale handle 7 , with the other hand on the main handle
24
All manuals and user guides at all-guides.com
15
and backing pad firmly together,
8 .
4 while turning the backing
onto the backing pad.
16 to hook and
onto spindle 8 , while depressing
Variable Speed Trigger Switch (Fig. A)
The variable speed trigger switch permits speed control from 0
. Holding
to 3500 RPM.
To turn the tool on, squeeze the trigger switch
you depress the trigger, the faster it will operate. Releasing the
trigger turns the tool off.
Use lower speeds for applying liquid waxes and polishes and
higher speeds for removing dried liquid.
Trigger Locking Button
The tool can be locked on for continuous use by squeezing the
trigger switch
in Figure A. Hold the lock button in as you gently release the
trigger switch.
To turn the tool off from a locked-on position, squeeze and
release the trigger switch once. Do not unplug the tool with
the switch in the locked-on condition. Make sure the tool is not
locked on when plugging in.
nOtE: The trigger switch can only be locked on with the tool
running at the maximum RPM designated by the speed control
wheel .
1
No-Volt Release
The variable speed trigger switch
function. In the event of a power outage or other unexpected
shut down, the trigger switch needs to be cycled (depress the
trigger switch, release, then depress again) to restart the tool.
Do not unplug the tool with the trigger switch in the locked-on
condition. Make sure the tool is not locked on when plugging
in. If the tool is plugged back in with the trigger switch in the
locked-on position, the tool will not run until the trigger switch
is cycled as described above.
Speed Control Wheel (Fig. A)
The maximum speed of your tool can be changed by rotating
the speed control wheel
versatility, the trigger switch
position and tool speed changed by means of the speed control
wheel alone.
The speed control wheel can be set for any speed between 600
and 3500 RPM and the variable speed trigger switch will then
control tool speed from zero to the wheel setting. For example:
A control wheel setting of 2200 RPM will allow the variable
speed trigger switch to operate the tool between zero and 2200
RPM, depending on how far the trigger switch is depressed.
Electronic Speed Control
The electronic speed control feature functions whenever the
trigger switch is fully depressed and the tool is running at the
selected speed determined by the setting of the control wheel.
As you load the tool by pushing it down on the work surface,
the tool will compensate for the loading and maintain the
selected speed. If the speed selected by the control wheel is
5 or
2200 RPM, the tool will maintain 2200 RPM, as it is loaded.
18 .
• The electronic speed control operates only when the trigger
switch 2
2 fully and depressing the lock button
2 has a no-volt release
1 to the desired setting. For added
2 may be locked in its full on
is fully depressed.
2 . The farther
6 shown