Black & Decker GL701 Traduction Des Instructions D'origine page 8

ENGLISH
♦ Place the new spool onto the boss in the spool
housing with the lines parked in the slots (23)
(fi g. F).
♦ Insert the line ends through the appropriate
eyelets (20) in the housing (10). Pull the slack
line until it pulls out of the parked slots (23)
(fi g. G).
♦ Align the tabs (17) on the spool cover with the
cut outs (21) in the housing.
♦ Push the cover (18) onto the housing (10) until
it snaps securely into place.
Note: Make sure that the cover is positioned,
listen for two audible clicks to ensure both tabs
(17) are correctly located.
Warning! If the cutting lines protrude beyond the
trimming blade (9), cut them off so that they just
reach the blade.
Winding new line onto an empty spool
(fi g. H - J)
You may wind new cutting line onto an empty
spool.
Replacement packs of cutting line are available
from your Black & Decker dealer (cat. no. A6171).
♦ Remove the empty spool from the appliance as
described above.
♦ Remove any remaining cutting line from the
spool.
♦ First wind new line onto the uppermost part of
the spool:
- Feed 2 cm of cutting line into one of the
slots in the upper section of the spool as
shown.
- Wind the cutting line onto the spool in the
direction of the arrow. Make sure to wind
the line on neatly and in layers. Do not
criss-cross.
- When the wound cutting line reaches the
recesses (22), cut the line.
- Temporarily park the line in the slots (23)
on one side of the spool as shown.
♦ Repeat the above procedure for the second
cutting line on the lower section of the spool.
Park the line in the unused slots (23).
♦ Proceed as described above to fi t the spool
on the appliance. Do not forget to release the
cutting line from the parking slots (23).
Warning! Only use the appropriate type of
Black & Decker cutting line. Ensure that cutting
line is present in both sections of the spool.
8
All manuals and user guides at all-guides.com
Mains plug replacement
(U.K. & Ireland only)
If a new mains plug needs to be fi tted:
♦
♦
♦
Warning! No connection is to be made to the
earth terminal. Follow the fi tting instructions
supplied with good quality plugs. Recommended
fuse: 5 A.
Troubleshooting
If your tool seems not to operate properly, follow
the instructions below. If this does not solve the
problem, please contact your local Black & Decker
repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
♦
♦
Automatic line feed does not work
♦
♦
♦
♦
♦
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
♦
♦
♦
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the new plug.
Connect the blue lead to the neutral terminal.
Check that the spool housing can rotate freely.
Carefully clean it if necessary.
Check that the cutting line does not protrude
more than 11 cm from the spool housing. If it
does, cut it off so that it just reaches the line
trimming blade.
Keep the tabs depressed and remove the
spool cover from the housing.
Pull the cutting line until it protrudes 11 cm
from the housing. If insuffi cient cutting line is
left on the spool, install a new spool of cutting
line as instructed above.
Align the tabs on the spool cover with the cut
outs in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just reaches
the blade.
Carefully clean the spool cover and housing.
Remove the spool and check if the lever can
move freely.
Remove the spool and unwind the cutting
line, then wind it on neatly again as described
above. Replace the spool as instructed.