Worx HandyCut WX424 Traduction Des Instructions Initiales page 15

3. ADjUSTING ThE 3-POSITION hANDLE
(See Fig. F)
Your saw has handle/motor housing with soft-
grip that adjusts to 3 different cutting angles,
0°, 15°, and 30°. This feature provides more
efficient cutting angles for various applications
and added gripping comfort with maximum
control.
Grasp the handle with one hand and push
the handle adjustment button "IN" to release
the handle for adjustment. Move the handle
forward or backward (See Fig. F) to locate the
3 different positions. When the handle moves
into 1 of the 3 positions the adjustment button
will snap out and the handle will lock into
position. When adjusting the handle, Always
be sure that the button has snapped out and
the handle is locked in position. If the handle
still moves forward or backward, repeat the
process until the handle is locked securely in
position.
wARNING: Do not operate the
saw if the handle is not locked in
position and can still move forward or
backward. Failure to lock the handle in 1
of 3 cutting positions could cause loss
of control of saw and result in serious
injury.
4. TRIGGER SwITch (See Fig. G)
To activate the trigger switch to turn the saw
"ON" , place your index and middle fingers into
the molded finger grip trigger safety release
switch, and the other two fingers on the
trigger paddle (See Fig. G). Squeeze the finger
grip "back" until it "clicks" , then depress the
trigger paddle to turn the saw "ON" . To stop the
saw, release your grip on the trigger paddle,
and the finger grip safety release switch will
move back into the "OFF" position.
5. USING ThE LASER LIGhT FEATURE
AND LED wORKLIGhT (See Fig. h, I)
wARNING: DO NOT stare into
beam. Only turn laser beam on
when the saw is on the work piece.
Your saw has a built-in laser light. To activate
laser light switch, saw must be plugged into
power source.
a. Do not turn the laser beam on until the saw
Mini multi-function saw
All manuals and user guides at all-guides.com
b. Mark the line of cut on the work piece.
c. Adjust the cutting angle and cutting depth
d. Plug in the saw and push the laser switch
e. Always shut off the laser light when you
f. Your circular saw has a built-in work light
6. STARTING A cUT (See Fig. j,K,L1,L2)
a) Set-up and clamp your work piece and
b) Set the handle on the saw to the desired
c) Set the depth of cut (with corresponding
d) Position the front of the saw's base onto
e) Manually release the blade guard release
f) With both hands on the handle, squeeze
g) Let the blade reach full speed before you
h) Press down on the saw, keeping the front
i) Carefully guide the saw through the line
is on the work piece.
as needed.
forward to turn on the laser.
are finished cutting.
for better visibility when cutting. To turn
on the LED work light, the saw must be
plugged in. Push the switch from OFF to
LED.
mark your cut line.
angle for your cutting application.
length of cut).
the leading end (edge) of the work piece
that is solidly supported. Align the center of
the "V" notch on the front of the base with
the cut line (See Fig. J).
lever while holding the finger lift bracket on
the rear of the base (See Fig. Ka, Kb) as you
lower the saw's handle and blade to the
selected depth.
Make sure the blade is not making
contact with the workpiece.
the trigger's molded finger grip safety
release "backward" while squeezing down
on the paddle switch to turn the saw "On" .
enter the work piece, starting your cut.
of the base flat against the work piece as
you slowly push the saw's blade into the
work piece (See Fig. Kc).
of cut. Do not bind the blade in the cut;
push the saw blade forward at a rate where
the blade is not laboring. When the cut is
complete, release the trigger safety release
and paddle switch and let the blade come
to a complete stop. Do not remove the saw
15 15
EN