Iqua miniUFO PHF-301 Mode D'emploi page 3

Refer to Fig 1 and Fig 2
Overview of the product
. Loudspeaker
2. Indicator Light Indicates status with blue and red lights
3. Volume Down button Decreases the volume
4. Volume Up button Increases the volume
5. Call button Answer a call, end a call, reconnect to phone, or switch
between handsfree and phone mode
6. Power button Switch the device on/off
7. Microphone
8. Charging connector
Sales package content
a. MiniUFO
b. Mounting plate with double-sided sticker
c. Sunvisor clip
d. Car charger with removable USB charging cable
e. User Guide
General Information
Thank you for purchasing Iqua miniUFO Bluetooth® Portable Handsfree. Your new device
is a stylish product that enables you to communicate comfortably with compatible mobile
phones that support Bluetooth wireless technology. In addition to being light and pocket-
sized, it has been designed for use in the car, at the office, or at home. You can charge the
device in your car with the car charger, which has a removable USB charging cable and is
included in the sales package.
Getting Started
Safety
• Always concentrate on traffic safety while driving and obey the law.
• The miniUFO is not a toy. Keep it away from small children since it contains small parts
that may pose a choking hazard.
Car Installation
You can attach your miniUFO to the sunvisor of your car with the sunvisor clip as shown in
Fig. 1 and 2. Alternatively, you can use the mounting plate that has a double-sided sticker
to attach it to the dashboard as shown in Fig. 3. Make sure that the product is not in the
operating area of any side impact airbags or any of the other safety or operating equipment
in your car. In addition, check that the product is securely fastened and does not interfere
with you being able to operate the vehicle.
Charging the battery
Before using the miniUFO, you must charge it for approximately 4 hours. Once the battery
is fully charged, it will provide up to 0 hours of talk time and up to 450 hours of standby
time. Always use the charger that comes in the sales package.
. Connect the charger cable to the miniUFO.
2. Plug the car charger into the cigarette lighter in your car. The red and blue lights will turn on.
3. The red light will turn off once the battery is fully charged.
You can also use the removable USB charging cable for charging the miniUFO from your
PC, which will take longer to charge as the power output of the USB port is lower than it
is with the car charger. The miniUFO indicates that its battery is low with a warning sound
and a flashing red light.
Once the charger is connected, the miniUFO turns itself off. Press the
miniUFO back on.
Switching on and off
To switch on the miniUFO:
• Press and hold the button until the blue light starts blinking (1 blink every 3 seconds).
• To switch off the miniUFO, press and hold the
Pairing the miniUFO and a mobile phone
Pairing is the process of linking your miniUFO to a Bluetooth-enabled mobile phone*. Once
this process is over, you will be able to use the miniUFO with the mobile phone you have
paired it to. If you want to use the miniUFO with another mobile phone, you must repeat
the pairing process again. Even though the miniUFO can be paired with up to 8 compatible
phones, it can only be connected to one phone at a time.
. Press and hold down the button until you hear a sound and the blue and red lights
start flashing in turns.
2. Release the button. The miniUFO is now in pairing mode and is waiting for your mobile
phone to contact it.
3. Complete the pairing with your mobile phone. Please refer to your mobile phone's
manual for details on how to search and pair. Once the mobile phone has found the
handsfree device, the phone will show Iqua miniUFO on its display. In order to pair with
the phone, enter the PIN code of the miniUFO, which is 0000.
4. After it has paired, the miniUFO will automatically connect to your mobile phone. Once
they have been successfully paired and connected, you will hear a sound and the blue
light will start flashing (3 flashes every 2 seconds).
* For the latest compatibility information please visit www.iqua.com.
Disconnecting the miniUFO from a phone
To disconnect the miniUFO from the phone it is connected to, do one of the following:
. Switch off the miniUFO.
2. Disconnect the miniUFO from the phone it is connected to in the phone's menu.
3 .Move the phone more than 10 meters away from the miniUFO.
Reconnecting the paired miniUFO to a phone
To reconnect the miniUFO to the last phone used, simply switch on the miniUFO and it
will automatically connect to the phone. If the miniUFO is already on, you can reconnect
to the last phone used by pressing the button of the miniUFO. Otherwise, make the
connection in the phone menu as instructed in your phone's user guide.
Call Functions
Answer a call
When there is an incoming call, you will hear the mobile phone's ringing tone through the
miniUFO speakers. To answer a call, just press the
End a call
To end an active call, press the button briefly.
Reject a call
When you receive an incoming call that you do not want to answer, simply press the
button for 3 seconds.
Redialing the last number dialed
To place a call to the last number dialed, press the
Adjusting volume
Adjust the volume by pressing the and buttons respectively.
Voice dialing (when supported by the phone)
To activate the voice dialing feature of your phone, press the
Please refer to your phone's user guide for additional details, especially as some phone
models do not support voice dialing. For optimal performance, connect your phone to the
miniUFO before recording voice tags.
Muting an active call
You can mute or unmute the miniUFO during an ongoing call by pressing the
All manuals and user guides at all-guides.com
button to turn the
button until the lights stop blinking.
button.
button for 3 seconds.
button for 3 seconds.
and
3
Product specifications
Model PHF-301
Size 98.6 (L) x 98 (W) x 27.5 (H) mm
Weight 8g
Talktime Up to 0 hours
Standby time Up to 450 hours
Charging time 3 hours max.
Battery type Lithium-Polymer battery 900 mAh
Bluetooth Standard Bluetooth Specification 1.2
Supported Bluetooth profiles Handsfree 1.0 and Headset 1.1
Connection Point-to-point
Paired Devices Up to 8, one at a time
Speaker Max ,5 W
Operating range Up to 0 meters
Operating temperature range -30ºC to +55ºC
buttons at the same time.
Switching the call between phone and handsfree mode
To transfer an active call from the miniUFO to your mobile phone, press and hold down the
button until the call is transferred to your phone. To transfer an active call from your
mobile phone to the miniUFO, press the button or use the functions of your phone as
instructed in its user guide.
How to erase paired devices
The MiniUFO can be paired with up to 8 Bluetooth devices. If you want to pair it with more
devices, you need to erase the paired device information. In paring mode, long press the
Volume down -button, it will erase all paired profiles and quit paring mode. At this time,
Blue LED gives 1 blink every 3 seconds.
Advanced Call Functions
If your mobile phone has call waiting or conference functions, you can do the following with
the miniUFO:
. A new call comes in during another call:
• Press the button for 3 seconds to put the current call on hold and accept the
incoming call.
• Press the button to end the current call and answer the new call.
2. Two calls, one active and the other on hold:
• Press the button for 3 seconds to toggle between the call on hold and the active call.
• Press the button to end the active call and accept the call on hold.
• Press the button for 3 seconds to merge the calls into a conference call.
Light indication summary
The miniUFO's LED lights can be either blue or red and are usually accompanied by a
sound signal.
The different signals indicate:
Blue light flashing once every 3 seconds power is on, no Bluetooth-connection
Blue light flashing three times every 2 seconds power is on, Bluetooth-connectionis open.
Blue and red light flashing in turns in pairing mode, waiting for user to
complete pairing with mobile phone
Red light flashing every 3 seconds low battery
Red and blue light stay on the battery is charging
Blue light on continuously charger connected, battery fully charged
Power Management
This product is powered by a built-in rechargeable battery which can not be changed. Do
not attempt to replace the battery. Rechargeable battery can be charged and discharged
hundreds of times, but it will eventually wear out. After a period of time that will vary
depending on the use and usage conditions you may find that the built-in battery will power
your product for only a couple of hours requiring you to charge more frequently.
Do charge your device only with the charger provided in the sales package. Unplug the
charger when not in use. Do not leave the device connected to the charger for longer
period than needed, since overcharging may shorten the battery lifetime.
If left unused a fully charged battery will discharge itself over time.
Temperature extremes may affect the ability of the battery to charge. Always try to keep
the device between 5°C and 25°C (59°F and 77°F). Leaving the device in hot or cold
places such as in closed car in summer or winter conditions will reduce the capacity and
lifetime of the battery. A device with hot or cold battery may not work for a while even when
the battery is fully charged. Battery performance is particularly limited in temperatures well
below freezing. Do not charge in humid environment.
Care and Maintenance
– Do not expose the device to liquid, moisture or humidity as it is not
waterproof.
– Do not use or store the device in dusty, dirty areas. Its moving parts and
electronic components can be damaged.
– Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
– Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic
circuit boards.
– Do not drop, knock, or shake the device. Rough handling can break internal
circuit boards and fine mechanics.
– Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
the device.
– Use a soft, clean, dry cloth to clean any lenses.
– Do not expose your device to contact with sharp objects as this will cause
scratches and damage.
– Do not stick anything inside the device as this may damage internal components.
– Do not dismantle the device or the charger as they do not contain serviceable
parts and taking apart the device may expose you to dangerous voltages or
other hazards.
Act according to your local rules and do not dispose of this product as part of your normal
household waste. Follow the applicable separate collection system for electrical and
electronic products.
How to get service for my IQUA Product?
If you believe that you are entitled to a repair or replacement of your IQUA product based
on your statutory rights under the applicable national laws relating to the sale of consumer
products or warranty given by the retailer who has sold the IQUA Product to you, please
contact your retailer.
DECLARATION OF CONFORMITY
We, Iqua Ltd., declare under our sole responsibility, that the product, PHF-301, conforms
with the provisions of the following Council Directive: 999/5/EC. A copy of the Declaration
of Conformity can be found at http://www.iqua.com/declaration_of_conformity.
Copyright © 2008 Iqua Ltd
EN