Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Start the engine only in accordance with the instructions.
-
Do not use any other methods for starting the engine!
-
Place the equipment on firm ground. Maintain good balance and secure
footing.
-
When pulling the starter knob, hold the equipment firmly against the ground
by your left hand. Never step on the drive shaft.
-
Before starting the engine, make sure that there is no person or animal in the
work area.
-
When starting the engine, keep the saw chain and guide bar clear of your
body and other object, including the ground. The saw chain may move when
starting and may cause serious injury or damage to the saw chain and/or
property.
-
The engine is to be switched off immediately in case of any engine problems.
-
Should the saw chain hit stones or other hard objects, immediately switch off
the engine and inspect the equipment.
-
Operate the equipment only with the shoulder strap attached which is to be
suitably adjusted before putting the equipment into operation. It is essential
to adjust the shoulder strap according to the user size to prevent fatigue
occurring during use. Never hold the cutter with one hand during use.
-
With the engine running only at idle, attach the shoulder harness. During
operation, keep the equipment on your right side firmly.
-
All protective installations and guards supplied with the machine must be
used during operation.
-
Never operate the engine with faulty exhaust muffler.
-
Except in case of emergency, never drop or cast the equipment to the ground
or this may severely damage the equipment.
Refuelling
-
Shut off the engine during refuelling, keep away from open flames and do not
smoke.
-
Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always
wear protective gloves during refuelling. Change and clean protective clothing
at regular intervals.
-
Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the equipment immediately after fuel has
been spilt.
-
Avoid any fuel contact with your clothing. Change your clothing instantly if
fuel has been spilt on it (to prevent clothing catching fire).
-
Inspect the fuel cap at regular intervals making sure that it can be securely
fastened and does not leak.
-
Carefully tighten the fuel tank cap. Change location to start the engine (at
least 3 meters away from the place of refuelling).
-
Never refuel in closed rooms. Fuel vapors accumulate at ground level (risk of
explosions).
-
Only transport and store fuel in approved containers. Make sure the fuel
stored is not accessible to children.

Method of operation

-
In the event of an emergency, switch off the engine immediately.
-
If you feel any unusual condition (e.g. noise, vibration) during operation,
switch off the engine. Do not use the equipment until the cause is recognized
and solved.
-
The saw chain continues to move for a short period after releasing the throttle
trigger. Don't rush to contact the saw chain.
-
Hold the front grip with the left hand and the rear grip with the right hand, no
matter you are right-hander or left-hander. Wrap your fingers and thumbs
around the grips.
-
Never attempt to operate the equipment with one hand. Loss of control may
result in serious or fatal injury. To reduce the risk of injury, keep your hands
and feet away from the blades.
-
Do not overreach. Keep proper footing and balance at all times.
-
Watch for hidden obstacles such as tree stumps, roots and ditches to avoid
stumbling. Clear fallen branches and other objects away.
-
If the equipment gets heavy impact or fall, check the condition before
continuing work. Check the fuel system for fuel leakage and the controls and
safety devices for malfunction. If there is any damage or doubt, ask Makita
authorized service center for the inspection and repair.
-
Do not touch the gear case. The gear case becomes hot during operation.
-
When you leave the equipment, even if it is a short time, always stop the
engine. The equipment unattended with the engine running may be used by
unauthorized person and cause serious accident.
• Resting
• Transport
• Refuelling
• Maintenance
• Tool replacement
5

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ey2650hg

Table des Matières