Publicité
Les langues disponibles
Les langues disponibles
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
CODE
H.00
EXTRA RINSE Upgrade Price - Increase or decrease between 0
EXTRA
and 200 by pressing the LEFT UPPER or RIGHT UPPER key pad.
RINSE
Factory preset for 1 coins = $0.25.
g Press the LEFT MIDDLE key pad once to advance to next code.
COIN/DEBIT OPTION
J.Cd
J.Cd
Both coin & debit selected.
J.C_
Coins selected, debit disabled. Press the LEFT LOWER key pad
3 times for this selection.
J._d
Debit Card selected, coins disabled. Press the LEFT LOWER key
pad 3 times for this selection.
J.Ed
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
g Press the LEFT MIDDLE key pad once to advance to next code.
L.00
PRICE SUPPRESSION OPTION
This option causes the customer display to show 'ADD' or
'AVAILABLE' rather than the amount of money to add. (Used
mainly in debit installations.)
L.00
Not Selected 'OFF'.
L.PS
Selected 'ON'. Press the LEFT LOWER key pad once for this
selection.
g Press the LEFT MIDDLE key pad once to advance to next code.
CLEAR ESCROW OPTION
n. CE
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
n. CE
Selected 'ON'.
n. 00
Not selected 'OFF'. Press the LEFT LOWER key pad once to
deselect this selection.
g Press the LEFT MIDDLE key pad once to advance to next code.
COIN (HUNDREDTH) INCREMENT OFFSET
U.00
U.00
For use with card reader applications only.
g Press the LEFT MIDDLE key pad once to advance to next code.
A3.02
NORMAL Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Normal is set to 02 from the
factory.
A4.00
DELICATES Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Delicates is set to 00 from the
factory.
A5.OF
POWERWASH Cycle Settings. Allows the owner to select the
cycle default options of Water Temperature, Soil Level, and Extra
Rinse.
See Table 1 for specific settings. Powerwash is set to 0F from the
factory.
EXPLANATION
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS.
2xxx Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the LOWER MIDDLE key pad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number in THOUSANDS.
4xxx Number in ONES.
5 xx Number of HUNDRETHS.
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
PD Models: Reinstall access door.
n
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
Table 1
A3, A4,
Extra
Soil
Wash
or A5
Rinse
Level
Temp
00
Off
Off
01
Off
Off
02
Off
Off
Warm
03
Off
Off
04
Off
On
05
Off
On
06
Off
On
Warm
07
Off
On
Technician Service Access Code
This method is only available on washers set to free vend (6 00).
To enter service mode:
Press the LEFT UPPER, RIGHT LOWER, RIGHT UPPER, and
LEFT LOWER key pads within 10 seconds.
To exit service mode:
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
1 02 = 2,000
2225 =
TOTAL CYCLES = 2,225
3 01 = $1,000.00
4600 = $ 600.00
5 75 = $
TOTAL = $1,600.75
A3, A4,
Extra
Soil
or A5
Rinse
Level
Cold
08
On
Off
Cool
09
On
Off
0A
On
Off
Hot
0b
On
Off
Cold
0c
On
On
Cool
0d
On
On
0E
On
On
Hot
0F
On
On
225
00.75
Wash
Temp
Cold
Cool
Warm
Hot
Cold
Cool
Warm
Hot
19
Publicité
