Télécharger Imprimer la page
NuTone 690UPGKIT Manuel D'instructions
NuTone 690UPGKIT Manuel D'instructions

NuTone 690UPGKIT Manuel D'instructions

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

BAT H FA N U P GRA D E K IT
RE A D A N D SAVE T HE SE INSTRUCT IO NS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service
panel. Lock or tag service panel to prevent power from being
switched on accidentally.
3. Installation work and electrical wiring (including switch location)
must be done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-rated
construction codes and standards.
4. Provide sufficient air for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the combustion equipment
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and local codes.
5. This product may have sharp edges. Be careful to avoid cuts
and abrasions during installation and cleaning.
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. Not for use in kitchens.
9. Acceptable for use over a bathtub or shower when installed
in a GFCI protected branch circuit.
10. This unit must be grounded.
11. This unit must be installed into fan housings that are marked
with the series number 690, 695 ,696, EC, or VSBP5. Other
fan housings cannot be substituted.
12. When local regulations include more restrictive installation
and/or certification requirements, those requirements
supersede the requirements of this document and the installer
agrees to conform to them at his own expense.
13. When installing, servicing or cleaning this unit, wear safety
glasses and gloves.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Install fan at least five feet (1.52 m) above floor.
3. To avoid motor bearing damage and noisy, unbalanced
impellers, keep drywall spray, construction dust, etc. off
motor and impeller.
4. Read specification label on product for information and
requirements.
Register your product
online at www.nutone.ca
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive
appearance – lower or remove grille and vacuum interior of
fan with a dusting brush attachment.
The motor is permanently lubricated and never needs oil-
ing. If the motor bearings make excessive or unusual noise,
replace the motor with the exact service motor. The impeller
should also be replaced.
To remove blower assembly - See step 3 on page 2.
OPERATION
Use an on/off switch, timer, or speed control to operate this ventilator.
WARRANTY
BROAN-NUTONE CANADA INC.
ONE YEAR LIMITED WARRANTY
Broan-NuTone Canada warrants to the original consumer purchaser
of its products that such products will be free from defects in materials
or workmanship for a period of one (1) year from the date of original
purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one year period, Broan-NuTone Canada will, at its option,
repair or replace, without charge, any product or part which is found to
be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP
STARTERS OR TUBES, BULBS OR BATTERIES, FILTERS, DUST,
ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR
DUCTING. This warranty does not cover (a) normal maintenance
and service or (b) any products or parts which have been subject to
misuse, negligence, accident, improper maintenance or repair (other
than by Broan-NuTone Canada or an authorized representative), faulty
installation or installation contrary to recommended installation instructions.
The duration of an implied warranty is limited to the one year period as
specified for the express warranty.
BROAN-NUTONE CANADA'S OBLIGATION TO REPAIR OR
REPLACE, AT BROAN-NUTONE CANADA'S OPTION, SHALL BE
THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. BROAN-NUTONE CANADA SHALL NOT BE LIABLE
FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES
ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR
PERFORMANCE. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone Canada
at the address or telephone number stated below, (b) give the model
number and part identification and (c) describe the nature of any defect
in the product or part. At the time of requesting warranty service, you
must present evidence of the original purchase date.
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest Broan-NuTone Canada Inc. dealer:
Dial Toll Free: 1-888-882-7626
Please be prepared to provide:
• Product model number • Date and proof of purchase
• The nature of the difficulty
Broan-NuTone Canada Inc. 1140 Tristar Drive,
Mississauga, Ontario L5T 1H9
MODEL 690UPGKIT
Page 1
Released Oct. 2011

Publicité

loading

Sommaire des Matières pour NuTone 690UPGKIT

  • Page 1 OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 6. When cutting or drilling into wall or ceiling, do not damage During this one year period, Broan-NuTone Canada will, at its option, electrical wiring and other hidden utilities. repair or replace, without charge, any product or part which is found to 7.
  • Page 2 MODEL 690UPGKIT Page 2 INSTALLATION 1. Disconnect the electrical power supply 3. Remove blower assembly from and lock out the service panel for the existing fan (cont’d). existing fan. 2. Remove grille from the existing fan. SPRING GRILLE Pull grille down to expose two springs. Squeeze each spring together and pull down again to release springs from motor plate slots.
  • Page 3 MODEL 690UPGKIT Page 3 6. Install new grille. 5. Install new blower into the existing fan housing. GRILLE SPRING MOTOR PLATE SCREW NEW GRILLE 2 TABS Squeeze one grille spring together and insert it into the & matching slot in motor plate. Repeat with the other grille SLOTS spring.
  • Page 4 NuTone also recommends to contact a NuTone certified service depot for all replacement parts and repair.
  • Page 5 CONVENANCE DANS UN BUT PARTICULIER. 6. Lorsque vous coupez ou perforez un mur ou un plafond, prenez Pendant cette période de un an, Broan-NuTone Canada, à son choix, garde de ne pas endommager les fils électriques ou autre réparera ou remplacera gratuitement tout produit ou pièce qui s’avère défectueux dans des conditions normales d’utilisation et d’entretien.
  • Page 6 MODÈLE 690UPGKIT Page 6 INSTALLATION 1. Couper l’alimentation électrique du 3. Retirer l’assemblage moteur ventilateur actuel et verrouillez le du ventilateur actuel (suite). panneau de distribution. 2. Retirer la grille du ventilateur actuel. RESSORT GRILLE Abaisser la grille pour accéder aux ressorts. Serrer chacun des ressorts et les abaisser pour les dégager des fentes de...
  • Page 7 MODÈLE 690UPGKIT Page 7 5. Installer le nouveau ventilateur dans le 6. Installer la nouvelle grille. boîtier existant. RESSORT DE LA GRILLE PLAQUE DU MOTEUR NOUVELLE GRILLE 2 PATTES Serrer le ressort de la grille et l’insérer dans sa fente dans ET FENTES la plaque du moteur.
  • Page 8 NuTone sont spécialement conçues pour satisfaire toutes les normes de certification de sécurité applicables. Leur remplacement par des pièces ne provenant pas de NuTone pourrait ne pas assurer la sécurité de l’appareil, entraîner une réduction sévère des performances ainsi qu’un risque de défaillance prématurée.