Makita 6827 Manuel D'instructions page 5

ENGLISH
1 Front cap
2 Locator
3 Adjusting ring
SPECIFICATIONS
Model
Capacities
Self drilling screw ................................................. 6 mm
Machine screw ..................................................... 8 mm
Wood screw ...................................................... 6.2 mm
–1
No load speed (min ) ...................................... 0 – 2,500
Overall length .................................................... 304 mm
Net weight .............................................................. 1.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Removing or installing the bit (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the bit.
To remove the bit, first pull the front cap off and then pull
the bit firmly. To install the bit, insert it into the tool as far
as it will go and then replace the front cap.
All manuals and user guides at all-guides.com
Explanation of general view
4 Pointer
5 Switch trigger
6 Lock button
6827
ENB004-1
7 Reversing switch lever
8 Hook
Depth adjustment (Fig. 2, 3 & 4)
When you wish to drive self drilling screws, etc., adjust
the depth as follows.
Turn the locator to adjust the depth.
Initially, adjust the locator to create a distance of approxi-
mately 1 mm from the tip of the front cap (which works in
conjunction with the locator) to the base of the screw
head. One full turn of the locator equals 1 mm change in
depth. After adjusting the locator, turn the adjusting ring
so that the 6" mark is aligned with the pointer on the gear
housing. Drive a trial screw into your material or a piece
of duplicate material. If the depth is not suitable for the
screw, adjust the locator until the proper depth setting is
obtained.
Adjusting fastening torque (Fig. 5)
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjust the
fastening torque as follows.
The fastening torque may be adjusted by turning the
adjusting ring. Before turning the adjusting ring, turn the
locator in the direction of the arrow as far as it will go
without forcing. The torque is increased by turning the
adjusting ring in the direction of the arrow and decreased
by turning it in the opposite direction. Align the number 1
on the adjusting ring with the pointer on the gear hous-
ing. Drive a trial screw into your material or a piece of
duplicate material. If the fastening torque is not suitable
for the screw, continue adjusting until the proper torque is
obtained.
CAUTION:
The adjusting ring should be turned only within the num-
bered range. It should not be forced beyond this range.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop. For continuous operation, pull the trig-
ger and then push in the lock button. To stop the tool from
the locked position, pull the trigger fully, then release it.
NOTE:
Even with the switch on and motor running, the bit will not
rotate until you fit the point of the bit in the screw head
and apply forward pressure to engage the clutch.
5