Publicité
Les langues disponibles
Les langues disponibles
2. Squeeze the trigger.
3. Cut with trimmer line at an angle using the tip (H1).
4. Swing trimmer in and out of the cutting area taking
small cuts (H2).
Using the Plant & Tree Guard (J1) & (J2)
The plant and tree guard allows the trimming of grass
close to plants and trees without damaging them with the
trimmer line.
1. Flip the guard down (J1).
2. Use the trimmer around trees (J2) and near plants.
EDGING
1. To convert to edging mode, press the button (K1) and
twist the cutting module (K2). An audible "click" will
confirm that the cutting module is locked. Ensure the
plant and tree guard is flipped upwards (K3).
a WARNING: Unplug the power tool from the power
source before performing maintenance. Severe
injury or death could occur from electrical shock
or body contact with moving parts.
AUTOMATIC TRIMMER LINE FEED SYSTEM
How the automatic trimmer line feed works
When initially switching on the trimmer, a small length of
trimmer line is fed out. A 'clattering' noise will be heard
when the trimmer line hits the trimmer line cutter (F1). This
is normal. After approximately 5 seconds the trimmer line
will be cut to the correct length and the noise will reduce
as the motor reaches full speed.
If the noise of the trimmer line being cut cannot be heard,
more trimmer line will need to be fed out. To feed more
trimmer line, stop the trimmer and allow the motor to stop
completely, then re-start, allowing the motor to reach full
speed.
Repeat until you hear the trimmer line hitting against the
cutter. Do not repeat this procedure more than 6 times.
Make sure the motor is up to full speed before trimming.
To manually feed the trimmer line (Q)
If required, the trimmer line can be fed out manually.
To operate:
1. Press and release the manual trimmer line feed button
(Q1) while gently pulling on one of the trimmer lines
until the trimmer line reaches the trimmer line cutter.
2. When the required amount of trimmer line is fed out,
gently pull on the second trimmer line. There is no
need to press the manual trimmer line feed button
again.
If the trimmer line extends past the trimmer line cutter, too
much trimmer line has been fed out. If too much trimmer
line is fed out, remove the spool cap and turn the spool
counter-clockwise until the trimmer line is at the desired
length.
To remove the spool cap (R)
1. Press and hold in the two spool cap release latches
(R1).
2. Pull the spool cap (R2) away from the spool holder
(R3).
When re-installing the spool cap
1. Clean all areas of the spool cap and spool holder.
Failure to do so may prevent the spool cap from being
correctly installed in the spool holder.
2. Replace the spool cap, pressing firmly down towards
the spool holder until the spool cap clicks into place.
3. Check that the spool cap is correctly installed by trying
to remove it without pressing the two latches.
8
All manuals and user guides at all-guides.com
2. Ensure the trimmer is in the correct position for edging
3. Hold the trimmer as shown (G).
4. Squeeze the trigger.
5. Use the wheel for extra stability and line up the edge
6. To stop the trimmer, release the trigger.
7. To return to trimming mode, press the button and twist
SHRUBBING
Press the lever (N1) with your foot to lower the handle.
The handle can be lowered into three different positions
to enable the use of the trimmer under shrubs and low
obstacles (P).
MAINTENANCE
To replace the spool and trimmer line complete (S)
1. Remove the old spool.
2. Place the new spool into the spool holder with the
3. Release one trimmer line from the notch and feed the
4. Repeat for the second trimmer line. Ensure the spool
5. Install the spool cap.
To replace the trimmer line on the spool (T)
IMPORTANT - Always wind the trimmer line onto the
upper section of the spool first.
1. Cut approximately 6 meters (20 ft) of trimmer line.
2. Insert 15 mm (0.6 in) of trimmer line into one of the
3. Wind the trimmer line in the direction of the arrows
4. Leave approximately 100 mm (4 in) of trimmer line
5. Repeat on the lower section of the spool.
6. Install the spool and the spool cap.
After you have finished using the trimmer:
1. Disconnect from the outlet.
2. Remove debris from the trimmer shaft, handles and
3. Use a soft brush to remove debris from the inside of
4. Inspect the trimmer carefully, especially the parts of
6. Store in a cool, dry place and out of reach of children.
Cable Storage (X1) & (X2)
The power cable can be stored on the trimmer.
1. Wind the power cable carefully to avoid kinking.
2. Press the button and the cable hook will drop down
3. Place the power cord onto the cable hook.
4. Push the cable hook fully back into position.
(L).
of the lawn with the two indicators on the guard (M1).
Edge in the direction indicated (M).
the cutting module the opposite way. An audible "click"
will confirm that the cutting module is locked.
cutout areas of the spool aligned with the eyelets.
trimmer line through the eyelet.
is correctly installed by gently rotating while keeping
the spool holder steady.
holes in the upper section of the spool.
on the top of the spool. Care should be taken to
ensure that the trimmer line is neatly wound on the
spool. Failure to do so will impair the efficiency of the
automatic trimmer line feed.
unwound and place into the notch.
vents with a soft brush or dry cloth. Never clean the
trimmer with water, cleaning fluids, or solvents (W).
the guard, the trimmer head and the motor housing air
vents (V).
the trimmer head. If the trimmer is damaged in any
way, contact an authorized service center. Never use a
damaged trimmer.
(X2).
Publicité
