Publicité
Les langues disponibles
Les langues disponibles
To reduce the risk of electric shock, use the power tool
only with an extension cord intended for outdoor use, such
as an extension cord of cord type: SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.
When using an extension cord, be sure to use one heavy
enough to carry the current that your power tool will draw.
An undersized extension cord will cause a drop in line
voltage resulting in loss of power and overheating. The
table below shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
Minimum gauge for extension cords
Volts
Total length of cord
7.6 m
(25 ft)
120V
18
a WARNING! Do not connect the power tool to the
power supply before it is completely assembled.
ASSEMBLY OF UPPER HANDLE TO TUBE (A1)
Ensure that the internal cable is not twisted.
1. Insert the shaft into the upper handle.
2. Push until it clicks into position.
Ensure that the shaft is fully installed by attempting to
remove it.
ASSEMBLY OF CUTTING MODULE TO SHAFT
(A2)
Ensure that the internal cable is not twisted.
1. Insert the shaft into the cutting module.
2. Push until it clicks into position.
Ensure that the shaft is fully installed by attempting to
remove it.
GUARD ASSEMBLY (B1, B2)
1. Position the guard (B1) over the trimmer head (B2).
Ensure the trimmer line is fed through the hole in the
guard.
2. Push the guard into place and turn it in the direction
indicated until a click is heard and the guard is
securely locked.
BEFORE STARTING
a WARNING
•
The use of eye protection is recommended.
•
Do not lean over the trimmer while trimming or
edging, objects may be thrown by the trimmer line.
•
Do not allow trimmer head to rest on the ground.
•
Do not overload the trimmer.
•
Unplug the power tool from the power source
before making adjustments.
• Make sure you have the proper personal protective
equipment.
• Inspect the cleanliness of the power tool. Make sure the
handles are dry, clean, and free of oil and grease.
• Inspect for correct alignment of moving parts.
• Inspect for broken or damaged parts. Do not use the
power tool if any damage affects safety or operation.
Have damage repaired by an authorized service center.
• Inspect the power cord. If it is damaged, have it repaired
All manuals and user guides at all-guides.com
15.2 m
30.4 m
45.7 m
(50 ft)
(100 ft)
(150 ft)
AWG
16
16
12
ASSEMBLY
OPERATION
VIBRATION EXPOSURE
Exposure to vibrations through prolonged use of power
tools could cause blood vessel or nerve damage in the
fingers, hands, and joints of people prone to circulation
disorders or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in skin color or
texture, or loss of feeling in the fingers, hands, or joints,
discontinue the use of this power tool and seek medical
attention. An anti-vibration system does not guarantee
the avoidance of these problems. Users who operate
power tools on a continual and regular basis must closely
monitor their physical condition and the condition of the
power tool.
Ensure the guard is securely in place by attempting to
twist the guard.
LOWER HANDLE ASSEMBLY (C)
1. Depress the two buttons on the sides of the switch
handle.
2. Locate the steady handle over the buttons and release
the buttons.
3. Adjust the steady handle to the most comfortable
operating position by depressing the buttons and
moving the handle.
HEIGHT ADJUSTMENT (D)
1. Turn height adjuster (D1) in the direction indicated to
un-lock (D2).
2. Adjust the length of the tube to the most comfortable
operating position.
3. Turn height adjuster in the opposite direction to lock
(D3).
Ensure that the shaft is fully secured.
CORD RESTRAINT (E1) & (E2)
1. Make a loop in the extension cord and push the loop
through the slot in the handle.
2. Position the loop over the hook and pull the cord back
through the slot.
by an authorized service center.
• Inspect the extension cord. Replace it if it is damaged.
• Connect the power cord to the extension cord.
• Connect the extension cord to the power supply.
Keep the extension cord clear of the work area. Position
the cord so that it will not get caught on bushes, hedges,
tree trunks or other obstructions while you are working.
a WARNING: Check the extension cord before each
use and frequently while working. If damaged,
replace immediately. Never use the tool with a
damaged cord since touching the damaged area
could cause electrical shock, resulting in serious
injury.
STARTING AND STOPPING THE TRIMMER
To start the trimmer, squeeze the trigger.
To stop the trimmer, release the trigger.
TRIMMING
1. Hold the trimmer as shown (G).
7
Publicité
