Makita BLS713 Manuel D'instructions page 13

ENGLISH
(Original instructions)
1 Stopper pin
2 Bolt
3 Adjusting bolt
4 Red part
5 Button
6 Battery cartridge
7 Star mark
8 Blade guard
9 Blade guard A
10 Blade guard B
11 Thumb screw
12 Kerf board
13 Saw blade
14 Blade teeth
15 Left bevel cut
16 Straight cut
17 Guide fence
18 Turn base
19 Top surface of turn table
20 Periphery of blade
21 Adjusting screw
22 Stopper arm
23 Pointer
24 Miter scale
25 Lock lever
26 Grip
27 Lever
28 Release button
SPECIFICATIONS
Model
Blade diameter ................................................................................................................................................... 190 mm
Hole (arbor) diameter ............................................................................................................................................ 20 mm
Max. Miter angle .................................................................................................................................. Left 47°, Right 57°
Max. Bevel angle ................................................................................................................................... Left 45°, Right 5°
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Miter angle
0°
45° (left and right)
57° (right)
–1
No load speed (min ) ............................................................................................................................................ 2,200
Dimensions (L x W x H) .....................................................................................................655 mm x 430 mm x 454 mm
Net weight ............................................................................................................................................................ 12.7 kg
Rated voltage .................................................................................................................................................... D.C. 18 V
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thickness.
2: When using a wood facing 15 mm thickness.
3: When using a wood facing 10 mm thickness.
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
All manuals and user guides at all-guides.com
Explanation of general view
29 Bevel scale
30 Arm
31 Screw
32 Switch trigger
33 Lock-off button
34 Hole for padlock
35 Wrench holder
36 Pipe holder
37 Center cover
38 Socket wrench
39 Hex bolt
40 Safety cover
41 Shaft lock
42 Arrow
43 Blade case
44 Hex bolt (left-handed)
45 Outer flange
46 Inner flange
47 Spindle
48 Dust bag
49 Dust nozzle
50 Fastener
51 Support
52 Vise arm
53 Vise rod
54 Holder
55 Holder assembly
56 Vise knob
45° (left)
25 mm x 300 mm
—
25 mm x 212 mm
—
—
—
57 Projection
58 Vise shaft
59 Base
60 Rod 12
61 Clamp screw
62 52/38° type crown molding
63 45° type crown molding
64 45° type cove molding
65 Inside corner
66 Outside corner
67 Over 15 mm (5/8")
68 Over 420 mm (16-1/2")
69 Holes
70 Set plate
71 Cut grooves with blade
72 Triangular rule
73 Arm holder
74 0° bevel angle adjusting bolt
75 Left 45° bevel angle adjusting
bolt
76 Limit mark
77 Brush holder cap
78 Screwdriver
Bevel angle
0°
52 mm x 300 mm
*60 mm x 265 mm (Note 1)
52 mm x 212 mm
*60 mm x 185 mm (Note 2)
52 mm x 163 mm
*60 mm x 145 mm (Note 3)
BLS713
5° (right)
40 mm x 300 mm
—
—
—
—
—
13