Overhauling; Disposal; Troubleshooter's Checklist; Warranty - Terrier TS Mode D'emploi

7c DISASSEMBLING/ASSEMBLING TSU, STSU, TSEU, TSU-R, TSHPU CLAMP MODELS
- Open the clamp to its full extent.
- Remove the tension spring (9) in the case
of the 0,75 TSU, 1TS(E)U , 1,5 TSU , 2 & 3
TSEU first remove the retaining pin (10) in
the cam assembly (2).
- Remove the retaining pin (10) and the
cam pin (7).
- Take the retaining pin (10) out of the con-
necting piece (18) and remove the link pin
(17).
- Remove the lifting shackle (16).
- Push the connecting piece (18) in until the
shackle pin (6) can be removed through
the mounting hole.
- Remove the connecting piece (18) and the
cam assembly (2).
- Disassemble the lever (4) by removing the
retaining pin (10) and take the lock as-
sembly (3) out of the clamp.
- Remove the pivot (8) using a socket and
ring spanner.
- Clean all parts with a standard degrea-
sant.
- Grease all shackle pins with bearing
grease.
- Oil the spring if necessary.
- Assemble all the parts in reverse order.
- Always insert new original retaining pins (10) and do so with the aid of a hammer, com-
bination pliers and pin punch.
- Always fit a new pivot bolt (11) and nut (12).
- Always use original Terrier components when replacing parts.
- Remove any burr with a file.
8

OVERHAULING

At least once a year, or if occasioned by damage to the clamp, the lifting clamp should be
inspected, tested and if necessary overhauled by Terrier Lifting Clamps B.V. or another re-
cognized mechanical repair and service center. If in doubt refer to your supplier.
9

DISPOSAL

Once it has reached the end of its useful life, the clamp can be treated as scrap iron, provi-
ded that the clamp is rendered unfit for use.
16
10

TROUBLESHOOTER'S CHECKLIST

Failure/malfunction Possible Cause
Load slipping Load dirty
Pivot dirty
Pivot and/or cam blunt
Jaws bent open
Lifting shackle pivoting badly Lifting shackle overloaded Reject clamp
Fork is pivoting badly Fork overloaded
Body bent Clamp overloaded
Lifting shackle oval shape Clamp overloaded
Spring defective Spring worn out
Shackle pins bent Clamp overloaded
Retaining pins missing Incorrectly assembled
Clamp difficult to open/close Key way slot dirty
Clamp worn out
Clamp contaminated
11

WARRANTY

Terrier Lifting Clamps provides a 5 year warranty on its lifting clamps. This warranty is ap-
plicable to the original end user of the lifting clamps. Only if the clamp has been inspected,
checked and maintained by this instructions and by an official dealer. This warranty period
of 5 years is valid from the day of purchase, and is liable to all conditions and measurements
stated in this document.
11a CONDITIONS
This warranty only covers failures in the lifting tools which is the consequence of production
errors which occur during normal use. The warranty covers no wear to components such as
pivots, cam assemblies, lock springs etc. Should there be any kind of failure within this gua-
rantee period, the lifting tool will be replaced or repaired to insight of the producer
No warranty is given to clamps due to the following failures:
- Regular wear
- Overload.
- Wrong and/or carelessly use
- Damages
- Not following procedures and measures
- Hoisting differing material other then indicated on clamp or stated in the user-manual
- Adapting and/or modifying of the Terrier clamp.
- The injudicious use of the clamp, and not succeeding all indications which are stated in
the users manual.
- When maintenance and/or revision has not been carried out by an authorised Terrier dis-
tributor.
Action
Clean load
Clean clamp
Overhaul clamp
Reject clamp
Reject clamp
Reject clamp
Reject clamp
Overhaul clamp
Reject clamp
Fit new retaining pins
Clean clamp
Reject clamp
Clean clamp
17