Sammic BE-10 Mode D'emploi page 4

INSTRUCTIONS
All machines carry the following information:
- Name and address of the manufacturer: SAMMIC
S.L - Basarte 1 Azkoitia. Guipuzcoa (SPAIN)
- The machine model is shown in the next section.
- The serial number is shown on the guarantee
sheet and on the declaration of conformity.
MODELS
This manual describes the
operation and maintenance of the BE-10, BE-
20, BE-20I and BE-40 planetary mixers.
The reference number of the model and its
specifications are shown on the identification
plate attached to the machine.
These mixers are designed and manufactured
in accordance with the following Standards:
- Standards for machine safety: ANSI/UL-763.
- Standards for hygiene and food equipment
materials: ANSI/NSF 8.
INSTALLATION
Please follow the instructions in this manual
carefully to ensure the best performance and
preservation of the machine.
L
OCATION
Screw or unscrew the three adjustable feet to
level the machine and ensure that it is perfectly
stable when operating at maximum speed.
E
LECTRICAL CONNECTION
1. Specifications.
- The mixer is supplied for a voltage of single
phase 208-240V 50-60 Hz.
- The motor of all models is triple phase and is
controlled by a speed reducer.
- The configuration of the reducer must
never be changed.
- THE MACHINE MUST BE EARTHED. The
speed reducer is fitted with a filter that carries
any interference to earth. This may cause the
differential switch to act strangely. We
recommend you use your own differential
switch or a "super-immunised earth leakage
protection" device for the machine .
- Prepare a wall socket with a 20 amp earth
leakage and thermal magnetic circuit breaker
and its corresponding plug. Place the switch or
plug in a convenient position to allow the
machine to be disconnected.
4 EN
2. Cable specifications:
SAMMIC mixers are supplied with a 1.5 metre
electric cable with a thermoplastic coating.
THE MACHINE MUST BE EARTHED. The
earth wire of the machine is clearly
identified.
ELECTRONIC CONTROLLER FUNCTIONS
Figure 1: Display (L)
installation,
Displays the time in operation, speed and
various warnings. When you connect the
machine the display shows two horizontal lines
indicating standby, while the" time" (1) and
"speed" (2) LED's are off.
Figure 1: Function (A)
Press function to select the function to be
displayed - time or speed. Speed is selected if
pilot light (1) is on. Press "Function" (A) again to
see speed and pilot light (2) lights up. It can be
pressed with the motor on or off.
Figure 1: Up (H)
Each press increases the value selected on the
display.
Figure 1: Down (H)
Each press decreases the value selected on the
display or.
Figure 1: Start (B)
Starts the motor if the safety guard is closed and
the bowl in position. If either of the two safety
devices is missing when you press start, the
display shows "SE" (security) to show that a
safety device must be enabled for the machine
to start.
Figure 1: Stop (G)
The first press stops the motor and the display
starts flashing to show it is in standby mode. It
still stores the time and speed values. After 3
minutes, or when you press "stop" again, the
machine loses these values and returns to its
initial status. You will see 2 horizontal lines.
O
PERATION
Time Control: Viewed when the "time" pilot light (1)
is on. It can be changed with the motor on or off.
- Continuous operation: a rotating line on the
display shows that it has been selected.
- Timed operation: From 30 seconds to 30
minutes. Between 30 seconds and 10
minutes, select the time in 30-second
intervals. From 10 minutes onwards, select
the time in 1-minute intervals. The display
shows the countdown in the same way except
for the last minute, which counts down in
seconds (shown by the illuminated dot in the
bottom right hand corner of the display). When
the programmed time is completed, the
machine stops and a beep is heard.
Speed Control: Viewed with the "speed" pilot
light (2) on. You can choose from 1-10 different
speeds. When the motor is on, the speed is
displayed and automatically changes to show
the time after 5 seconds. The speed can be
changed when the motor is on or off.
Standby: Shown with 2 horizontal lines. Press
start for continuous operation at minimum speed.
Energy-saving: If the machine is stopped for 5
minutes, the display switches off and only a dot
is shown. Press any key for the display to return.
START-UP
Before using the machine for the first time,
clean the area in contact with food with
(lukewarm) soapy water, rinse and leave to dry.
1. F
ITTING THE BOWL
- Place the bowl support at the lowest position.
- The bowl is attached to the support at three
points.
- Place the boiler so that the "MAX" label is visible.
- Ensure that touching surfaces are clean.
- Lift the bowl and pull outwards to remove it.
2. F
ITTING THE TOOLS
- Place the bowl support at the lowest position.
- Hook the tool on the tool holder.
- This is easier if the tool is fitted to the bowl
support previously.
3. S .
ELECT THE TIME AND SPEED
Adapt the speed and tool to the task being carried
out, remembering that available mixing strength
(torque) increases when the speed decreases.
4. O
PERATION
The mixer only starts if the bowl support is at the