Stiga MC 534 Serie Manuel D'utilisation page 34

5.2. SAFETY CHECKS
• Check the integrity and correct assembly of all machine
components;
• Make sure that all fasteners are tightened correctly;
• Keep every surface of the machine clean and dry.
Action
1. Start the machine.
2. Release the engine / cutting
means brake lever.
1. Start the machine.
2. Engage the drive lever.
3. Disengage the drive lever.
1. Test drive.
If any of the results fail to match the indications
provided in the tables, do not use the machine!
Contact a service centre to have it checked and
repaired if necessary.
5.3. START-UP AND WORK
NOTE Start the machine on a level surface free from obsta-
cles or grass.
• Models with manual starter hand grip (Fig. 11).
• Models with push-button electric starter control (Fig. 12).
IMPORTANT Always maintain a safe distance from the cut-
ting device while working, corresponding to the length of the
handle.
5.4. STOP
When you have finished working, release the engine brake
lever/cutting device (Fig. 12).
When you have stopped the machine, it will take
a few seconds for the cutting means to stop.
Do not touch the engine after it has been turned
off. Burn hazard.
5.5. AFTER OPERATION
• Cleaning procedure (Par. 5.1).
• If necessary, replace the damaged components and
tighten any loose screws and bolts.
Whenever you leave the machine unused or unattended:
• Remove the spark plug cap (for manual starter hand
grip models).
• Press the tab and remove the consent key (on models
with a push-button electric starter).
6. MAINTENANCE
The safety regulations to follow are described in chap. 1. Strictly
comply with these indications to avoid serious risks or dangers.
Before conducting any inspections, cleaning or maintenance/
adjustment interventions on the machine:
• Stop the machine.
• Make sure that every moving component has come to
Result
1. The cutting means should
move.
2. The levers must return to the
neutral position automatically
and quickly, the engine must
switch off and the cutting
device must stop within a few
seconds.
2. The machine moves forward.
3. The machine comes to a
standstill.
1. No abnormal vibrations.
No abnormal sound.
a standstill.
• Wait for the engine to cool down.
• Remove the spark plug cap.
• Remove the safety key or the battery on models with a
push-button electric starter control).
• Use suitable clothing, protective gloves and goggles.
6.1. CLEANING
Clean thoroughly following the instructions below every time
it is used.
• Wash the machine with water after each cut
• Remove grass debris and mud accumulated inside the
chassis.
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass
mulch, leaves or excessive grease.
6.2. CUTTING MEANS MAINTENANCE
All work on the cutting means (disassembly,
sharpening, balancing, repairing, reassembly
and/or replacing) are demanding jobs that require
special skills as well as special tools. For safety
reasons, these jobs are best carried out at a
Specialised Centre.
Make sure damaged, misshapen or worn cutting-
means are replaced, together with its own screws
in place to preserve balance.
IMPORTANT Always use original cutting devices with the
code shown in the "Technical Data" table.
6.3. RECHARGE THE BATTERY
The battery is supplied for electric push-button starter switch
models. Read the engine instruction manual for instructions
regarding autonomy, recharging, reinstating and maintenance
of the battery.
NOTE For more information on maintenance, please refer to
the full instruction manual.
7. TRANSPORT, STORAGE AND
DISPOSAL
7.1. TRANSPORT
Whenever the machine is to be handled, raised, transported
or tilted you must:
• Stop the machine.
• Make sure that every moving component has come to
a standstill.
• Remove the spark plug cap or remove the safety key or
battery (on models with a push-button electric starter
control).
• Wear heavy work gloves.
• Hold the machine in the points offering a safe grip, taking
into account the weight and its division.
• Use an adequate number of people suitable to the weight
of the machine.
• Make sure that machine movements do not cause damage
or injuries.
• Fasten firmly to the means of transport using ropes or
chains to prevent it from tipping over causing damage
and fuel leaks.
EN - 4