Bosch GBH Professional 2-26 RE Notice Originale page 14

OBJ_BUCH-279-005.book Page 14 Wednesday, December 12, 2012 2:05 PM
14 | English
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
 Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
 Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause hear-
ing loss.
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Hold the tool by the insulated gripping surfaces when
performing operations where the application tool or
the screw could contact hidden wiring or its own power
cord. Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the operator.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
1 609 92A 03Z | (12.12.12)
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
GBH 2-26 E/RE
The machine is intended for hammer drilling in concrete,
brick and stone. It is also suitable for drilling without impact in
wood, metal, ceramic and plastic. Machines with electronic
control and right/left rotation are also suitable for screwdriv-
ing.
GBH 2-26 DE/DRE/DFR
The machine is intended for hammer drilling in concrete,
brick and stone, as well as for light chiselling work. It is also
suitable for drilling without impact in wood, metal, ceramic
and plastic. Machines with electronic control and right/left ro-
tation are also suitable for screwdriving.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Quick change keyless chuck (GBH 2-26 DFR)
2 SDS-plus quick change chuck (GBH 2-26 DFR)
3 SDS-plus tool holder
4 Dust protection cap
5 Locking sleeve
6 Lock ring for rapid-change chuck (GBH 2-26 DFR)
7 Rotational direction switch (GBH 2-26 RE/DRE/DFR)
8 Lock-on button for On/Off switch
9 On/Off switch
10 Release button for mode selector switch
(GBH 2-26 DE/DRE/DFR)
11 Mode selector switch (GBH 2-26 DE/DRE/DFR)
12 Button for depth stop adjustment
13 Depth stop
14 Auxiliary handle (insulated gripping surface)
15 Release button for drilling/hammer drilling selector
switch (GBH 2-26 E/RE)
16 Selector switch for drilling/hammer drilling
(GBH 2-26 E/RE)
17 Handle (insulated gripping surface)
18 Securing screw for key type drill chuck*
Bosch Power Tools