Tecfrigo Ecodisplay 400 GS Installation Et Mode D'emploi page 7

6. CONNECTIONS TO MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate
2.
to the appliance. Ensure that the supply socket has the following characteristics:
earthed. It is appropriate for the nominal current as set out on the rating plate.
b)
IEC regulations: -Magneto-thermic differential switch with in=nominal value as stated on the rating plate;
-Differential with ID sensitivity = 30 mA.
4.
The connecting cable to the appliance is H05 VVF, designed for internal use only.
appliance, during the transport or storage, has been erroneously placed in horizontal position or upside-
down, it must be left in the correct vertical position for at least 3 hours before connecting it to the electrical
5.
supply. Insert the plug (do not use triple and reductions outlets) ( see picture 4).
7. CONTROLS
The controls of the appliance are situated at the front inside a protected rectangular recess. . 1 Light
switch: to switch on the light inside the appliance. 2 Refrigeration unit switch:
3 Thermometer:
system. .
temperature inside the appliance. In order to adjust the temperature: pushing once the button 4 "SET"
the display will show the temperature of the cell, pushing several times the button
temperature increases while pushing several times the button
(see picture 5).
8. CHECKING THE CORRECT FUNCTIONING BEFORE PLACING THE FOODSTUFF IN
MAKE SURE THAT 1
: . The plug is connected.
thermometer shows the desired temperature for the foodstuffs to be stored in. . The door is closed.
5.
The appliance is not exposed to the direct light of the sun or high powered lamps.
temperature does not exceed that in wiich the appliance is designed to work normally,i.e.
+30°CU.R.55%, (climatic class 4). . The compressor ventilation grilles are free from obstruction for at
8
least 30 cm. . The foodstuffs are placed on the shelves in the right way, in order to ensure a good
circulation of the cool air.
9. INTERNAL CLEANING
Model G/GS 1.
Switch off the appliance. . Open the door and remove the refrigerated goods. . Clean
the internal surfaces and the accessories of the appliance with a sponge dipped in water with a little
sodium bicarbonate. Dry with care.
Model GBT 1.
Switch off the appliance.
the door open and wait for the grills to defrost.
5
from the evaporator. . Clean the internal surfaces and the accessories of the appliance with a sponge
dipped in water with a little sodium bicarbonate. . Dry all parts with care before turning on the appliance
(see fig. 6).
10. REPLACEMENT OF THE INTERNA LIGHT
1
. Switch off electricity supply. . Unscrew the screws fixing the upper light holder. . Detach the
fluorescent tube from the upper lamp holder.
the transparent protective tube
reverse order (See picture 7).
11. REPLACEMENT OF THE DOOR'S MAGNETIC GASKET
1 2.
. Open the door. Take the magnetic gasket with your hands and remove it from the frame.
the new gasket and press all around it when in place (See picture 8).
das Schmiermittel
NICHT entfernen
für den ersten Monat
des Lebens.
Operator's guide
3.
Ensure that there is no danger of explosion (AD) in the room.
.
to read the temperature inside the appliance.
2.
The refrigeration switch is on (green light lit up).
7
2
2.
Open the door and remove the refrigerated goods. . Leave
4. N.B.:
6
2
4.
Remove the tube from the lower lamp holder. . Remove
(NO LED) 6.
. Replace the fluorescent tube. . Replace everything parts in
7
Thermostat:
6 "DOWN"
the temperature decreases
4
do not use pointed metal tools to remove the ice
7
NON rimuovere
il lubrificante
per il primo mese
di vita.
DO NOT remove
the lubricant
for the first month
of life.
(A)
attached
a) It is properly
It complies with the
c)
Notice:
in case of
to run the refrigeration
to adjust the
5 "UP"
the
3.
The
6.
The room
3
3
3
5
3.
Insert
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO