Tecfrigo Ecodisplay 400 GS Installation Et Mode D'emploi page 6

Operator's guide:
1. Unpacking instructions
2. The handles
3. Grill shelves
I
4. Cleaning of the internal
5. External cleaning
UK
6. Connections to mains
7. Controls
D
8. Checking the correct functioning
9. Internal cleaning
E
10. Replacement of the interna light
11. Replacement of the door's magnetic gasket
F
!
WARNINGS
NL
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety. 1. Adults should operate this appliance only. Do not allow children
P
to use the controls or play with it. . It is forbidden to modify in any way the main functions and
characteristics of this appliance. . The electrical installation of the appliance should be carried out by a
S
qualified electrician or other competent person. . Never attempt to carry out repairs unassisted. Inexpert
repairs can cause serious damage and malfunction. . Assistance has to be provided by an authorized
engineer only. Always use original spare parts. . This appliance is not suitable for the storage of basic
DK
commodities not including food-stuffs. . The manufacturers of this appliance accept no responsibility for
the consequences of misuse in contravention of these safety instructions. It further reserves the right to
FIN
carry out improvements without prior notice. 8. Avoid installing the cabinet directly in line with sunlight.
9
. Nevere install the appliance near sources of heat, such as radiators, stoves, etc.
B
ventilation grills free from obstruction for at least 30 cm.
shelves and grills do not hang over the edges.
GR
ice to form on the evaporator, we recommend stopping the compressor and placing the goods in special
refrigerated containers, kept at the same temperature, until defrosting is completed;if this is not carried
CZ
out the compressor will continue to operate leading to a wasteful consumption of electricity and poor
performance.
EE least 10 cm. Avoiding this, you will avoid also the consequent mildew formation and unpleasant smells.
LV
!
Our products are for internal use only do not install outside restaurants, shops.
LT
!
Do not keep the neon light up if the refrigeration is off.
H
M
1. UNPACKING INSTRUCTIONS
PL
CARDBOARD PACKAGING 1a. Cut surrounding tape. Remove the cardboard packaging by sliding
upwards. WOODEN CRATE 1b
SK
fork-lift truck between appliance and pallet or crate. . Lift the appliance
5
. Place the appliance on a horizontal level surface. . Pay attention anything is left inside the packing.
SLO
7
. Separate the packing materials according to their type, for easier disposal.
the holes on the back of the appliance (See picture 1).
2. THE HANDLES
1.
The handles will be found into a package inside the appliance. . Fix the base part of the handle using
the two screw inserted on the holes already. Tighten with care.
until it clicks into place (See picture 2).
3. GRILL SHELVES Model Ecodisplay / Snellè
If one or more grills need to be removed: . Remove the spacers that fasten the grills to the cabinet walls.
2.
Push the grill sideways until it comes out of the opposite side. . Tilt it
the grill,repeat the above operations in reverse order
1
.The support are in a pack inside the appliance. . Fix the supports, inserting the hook on the vertical
(B),
frames slits
on the supports, their raised edge opposite to the door (see fig. 3 / 9).
4. CLEANING OF THE INTERNAL
1. Only clean the internal components and glass panels with a soft, wet sponge and a neutral detergent.
2. Dry with care using a soft cloth
5. EXTERNAL CLEANING
1. For the glass panels use the same products as used for the internal cleaning.
2
3
7
13
. If the appliance is not working and unused, it is indispensable to keep the door open at
. Remove the nails from the wooden crate with care. . Insert forks of
pushing them downwards
Operator's guide
Maintenance manual (Page 48):
1. Cleaning the condenser
2. Wiring diagram diagram of refrigeration unit
4
5
6
11
. Ensure that the products displayed on the
12
. If damp air or products to be refrigerated should cause
3
6
2
3.
Place the plastic part and press down
1
3
2
(C ). 3
. The grid shelves are into a carton box. Place the grids
6
10
. Keep the
2
4
. Remove the pallet or crate.
8.
Put the two spacers in
(a) (b). 4
and pull it out . To refit