Operating Other Components Using The Remote Control; Setting The Manufacturer Code - Yamaha DVX-S100 Mode D'emploi

Masquer les pouces Voir aussi pour DVX-S100:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 80

OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL

Setting the manufacturer code (remote control signal
assigned to each manufacturer) for your TV, VCR or MD/
CD recorder on the remote control allows you to operate
not only the DVX-S100 but also your TV, VCR or MD/
CD recorder using the remote control.
Note
• Depending on the model, certain components from other
manufacturers cannot be controlled, or only limited functions
can be controlled, even though the proper manufacturer code
has been set. If you encounter this problem, please use the
remote control supplied with the component.

Setting the manufacturer code

Manufacturer codes can be set for TV, VCR and MD/
CD-R buttons only.
Note
• TV manufacturer codes can be set for the TV button only.
However, any of the manufacturer codes can be set for the VCR
and MD/CD-R buttons.
POWER
TV
TV
AV
TV MODE
INPUT
CH
MUTE
SUBTITLE
REC
CODE SET
CODE SET
SHIFT
HALL
JAZZ
1
2
SETUP
SPORTS
MONO MOVIE
5
6
PLAY MODE
/DTS
SELECT
9
0
TOP MENU
MENU
LEVEL
SET MENU
PRESET
CH
ENTER
PRESET
TEST
B. BOOST
ON SCREEN
RETURN
(U.S.A. model)
1
While pressing CODE SET, press the input
selector button (TV, VCR, MD/CD-R) for which
the manufacturer code is to be set.
Only one manufacturer code can be set for each input
selector button.
Note
• Keep pressing CODE SET between step 1 and 2.
• Refer to "LIST OF MANUFACTURER'S
CODES" at the end of this manual.
AV
POWER
SLEEP
TUNER
VOL
MD
MD/CD-R
CD–R
AUDIO
VCR
VCR
VIDEO 2
VIDEO 1
CD
DVD
AMP
ROCK
ENTERTAINMENT
3
4
Numeric buttons
ANGLE
MARKER
MOVIE 1
MOVIE 2
7
8
REPEAT
A–B
MATRIX 6.1
STEREO
> – 10
CANCEL
GROUP
PAGE
MUTE
ABCDE
CH
VOL
2
Keeping CODE SET pressed, enter the 1-
digit device code and the 2-digit
manufacturer code for the component to be
controlled using the numeric buttons.
You can release CODE SET after entering the code.
y
• The manufacturer code 99 has been set for the remote control
selector buttons (TV, VCR and MD/CD-R) at the factory.
3
Press POWER (TV or AV) and check that the
component to be controlled turns on and off
(standby).
Precautions when performing the setting
You can operate the component using the TV, VCR or
MD/CD-R operation buttons on the remote control once
the manufacturer code is set properly. If unsuccessful,
perform the procedure from step 1 again. Pay attention to
the following points when you perform the procedure.
• Check that the correct remote control selector button
has been selected when setting the manufacturer code.
• If more than one code is given for a manufacturer, try
entering each code in the order given.
• Remove and replace the remote control's batteries
(complete this step within 2 minutes) and then perform
the procedure. While replacing the batteries, be sure not
to press any button on the remote control. Doing so
may erase the manufacturer code which has been set
for other remote control selector buttons.
To reset the manufacturer code to the
factory-set code
Follow steps 1 to 2 for the procedure "Setting the
manufacturer code", and enter the device code for the
component and "99" while pressing CODE SET in step 2.
(It is not necessary to follow step 3.)
59

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dvr-s100Nx-s100sNx-s100cSw-s100

Table des Matières