Télécharger Imprimer la page

Black & Decker KC8482C Notice D'utilisation page 4

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 21
If charging problems persist, take or send
the tool, energy pack and charger to an
authorised service centre.
The energy pack should be recharged when it
fails to produce sufficient power on jobs which
were easily done previously. Do not continue to
use under these conditions. Follow the charging
procedure described above. You may also
charge a partially used pack whenever you wish.
1 hour charger only:
The charger and energy pack can be left
connected indefinitely. The charger will keep the
energy pack fully charged.
Switch and forward/reverse lever
(Figs. C1 - 4)
C
To turn the drill on, squeeze the trigger switch.
To turn the drill off, release the trigger switch
(Fig. C1).
The forward/reverse lever is a three position
lever located over the trigger switch in the
housing.
During charging, changing accessories
or storage, move the lever to the "Off"
position in the middle (Fig. C2).
Slide it to the right to drill holes or
drive screws (Fig. C3).
To remove screws or back out jammed
drill bits, move the lever fully to the left
(Fig. C4).
Two speed selector (Fig. D)
D
Your drill has a two speed mechanical gear
selector at the top of the housing. In order to
change the speed setting, allow the chuck to
rotate slowly by pressing gently on the
trigger switch.
To select the low speed setting, slide the
selector switch towards the front end of the
drill. The number 1 will appear on the
selector. This will produce a speed ideal for
screwdriving (Fig. D).
To select the high speed setting, slide the
selector switch towards the back end.
The number 2 will appear on the selector.
This will produce a speed ideal for drilling
and hammer drilling.
Warning! Do not change gear while the unit
is running.
Torque control (except KC8402C)
E
Your drill/driver is equipped with a torque
control mechanism to enable you to do
repetitive screwdriving.
ENGLISH
When screwing in the first screw,
determine the correct torque setting
which will result in the screw being flush
with the surface of the workpiece.
By keeping the same torque setting,
all following screws will also be flush with
the workpiece, due to the torque
mechanism which disengages the
power of the motor at the moment the
screw is flush.
This mechanism prevents damage to
the screwhead and the workpiece
(e.g. screws are not driven in too far).
Combination percussion action and
torque adjustment collar (KC8482C,
KC9682C & KC1282C)
These units are equipped with a combination
percussion action and torque adjustment
collar. To select for percussion action rotate
the collar until the hammer symbol is in line
with the indicator on the top of the drill
housing. To select the correct action for
non-masonry drilling tasks rotate the collar
until the drill bit symbol is in line with the
indicator on the top of the drill housing.
For screwdriving, these units are equipped
with 5 position collars, allowing adjustment
of the torque to suit the size of the screw
and the material involved. Before starting
work, adjust the torque in the following way.
Set the collar in position 1 and begin
screwdriving (low torque). If the machine
clutch ratchets too early, adjust the collar to
increase the torque as required.
Maximum recommended capacities
Steel
Wood
Masonry (combi only)
Chucks (Figs. F1 - 3)
Keyless chuck
F
To insert a drill bit or other accessory,
follow the steps listed below:
Switch the control lever to the
"Off" position.
8.4V
9.6V
12V
10mm
10mm
10mm
15mm
20mm
25mm
10mm
10mm
12mm
5

Publicité

loading

Ce manuel est également adapté pour:

Kc9682cKc1282cKc8452cKc8462cKc9662cKc8402c