Initial Setup; Performing An Automatic Channel Search - JVC LT-32HA48U Guide D'utilisation

Chapter 3 - Installing channels
Chapter 3

Initial setup

Initial setup involves selecting all the settings required
to be able to search for and store all the analogue
and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process.
Initial setup
Please select your language:
▲/▼
1. Press to select your language, then press
OK/► to enter the next step.
▲/▼
2. Press to select your country, then press
OK/► to enter the next step.
Note: If you select France, you will have to enter
the Password setting menu here in order to
set a password. Use the numeric buttons to
enter a four-digit number for your password.
(Your password cannot be 0000.) Re-enter
the same code to confirm the password.
After that, you will enter the next step
automatically. (In this step, you can only
press ◄ to return to the previous step.)
▲/▼
3. Press to select your tuner mode
Antenna or
- Select
• Press OK/► to enter.
▲/▼
• Press
to start the automatic search for all DVB-T
digital and/or analogue channels.
Cable.
- Select
• Press OK/► to enter.
▲/▼
• Press
to directly start your initial setup or enter below
step.
• Select Full if available to search for and store
all DVB-C digital and analogue channels.
• You may select another advanced scan
mode if available (for example, Advanced ),
Language
English
Български
Hrvatska
Česky
Dansk
Select Next
Cable.
Antenna.
to select Scan, then press OK/►
to select Scan, then press OK/►
then configure the correct cable information
as described below. Use the numeric buttons
to adjust the values for frequency, symbol
rate and network ID; use ◄/► to select a
modulation mode.
• Press OK to start initial setup relating to all
DVB-C digital and analogue channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before starting the scanning, you can also select
Skip scan to skip the initial setup process.
5. During the setup, you can follow the hints
available at the bottom of the screen to return to
the previous step by pressing ◄. Or press Exit to
exit or interrupt the search halfway.
6. Once the automatic search ends, the set enters
the next step automatically. Press
your location: Shop or Home. Press OK/► to
confirm your selection and enter the last step.
7. - In this step, you can press OK to exit the initial
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select Setup >
Organiser and press OK/► to enter.
- In this step, you can also press ◄ to return to
the previous step.

Performing an automatic channel search

This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels.
1. Press Menu on the remote control and select
Setup > Language > Menu language. Press
◄/► to select your desired menu language.
2. Press Menu to return to Setup. Press ▲/▼ to
select Country, then press ◄/► to select your
country. The TV installs and arranges channels
according to your country.
3. Press ▲/▼ to select Tuner mode, then press
◄/► to select
Antenna.
- Select
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
Automatic search
Automatic update
Analogue manual scan
Antenna manual installation
Clean channel list
Enter
Select
Back
Exit
• Select Automatic search, then press OK/► to
display Automatic search.
EN 8
Installing channels
▲/▼
to select
Antenna or Cable.
Channel install