For Your Safety - Bosch AQUATAK 1200 PLUS Instructions D'emploi

F016 L70 373 - GB Seite 3 Freitag, 21. Oktober 2005 11:10 11

For Your Safety

Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
Electrical Safety
Your machine requires an earth connection. The op-
erating voltage is 230 V AC, 50 Hz (for non-EU
countries 220 V, 240 V as applicable). Only use ap-
proved extension cables. Contact your Bosch Serv-
ice Centre for details.
If you want to use an extension cable when operat-
ing your high pressure washer, only the following ca-
ble dimensions should be used:
2
1.5 mm – max length 20 m
2
2.5 mm – max length 50 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the earth
cable of your supply network in accordance with pre-
scribed safety regulations.
If in doubt contact a qualified electrician or the near-
est Bosch Service Centre.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and intended
for outdoor use.
Cable connections should be kept dry and off
ground.
It is recommended for increased electrical safety to
use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your
RCD every time you use it.
For products not sold in GB: WARNING: For
safety, it is essential that the mains plug attached to
the product is fitted to the power supply cable. The
couplings of connection leads must be protected
against splashes and the coupling sockets on the
leads must be made of rubber or coated with rubber.
Fixing means for the connection leads must be
used.
If the supply cord is damaged, it must be replaced by
a Bosch Service Centre.
Products sold in GB only: Your product is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket out-
lets, it should be cut off and an appropriate plug fit-
ted in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
15 • F016 L70 373 • TMS • 14.09.05
Assembly
Water connection
Screw inlet connector 7 onto machine water inlet
A
connection 12.
/ Attach water supply hose (not supplied) to
A B
the mains water supply and machine.
Connecting high pressure water supply
hose/nozzle
Securely screw high pressure hose 6 onto ma-
C
chine at connection 13.
Inserting the vario-jet/fan power lance 4 into the
D
power gun 3. Depress and turn the vario-jet/fan
power lance 90° clockwise to lock in place.
Adjustments and using different
nozzles
Vario-jet-fan power lance
(yellow colour coded–AQUATAK 1200 PLUS
green colour coded–AQUATAK 1250)
Twist the front ring to adjust from a pencil to a fan
E
jet and vice versa.
Roto power lance
(red colour coded–AQUATAK 1200 PLUS/
yellow colour coded–AQUATAK 1250)
Turn the vario-jet/fan power lance 4 90° anti-
I
clockwise. Extract the vario-jet/fan power lance.
Insert the roto-power lance 9 into the power
J
gun 3. Depress and turn the roto-power lance 90°
clockwise to lock in place.
Detergent nozzle and bottle
AQUATAK 1200 PLUS
Turn the power lance 90° anti-clockwise. Extract
I
the power lance.
Insert the detergent-nozzle 8 into the power
F
gun 3. Depress and turn the detergent-nozzle 90°
clockwise to lock in place.
AQUATAK 1250
To apply the detergent twist the rear ring as
G
shown from high pressure mode to low pressure
mode.
To adjust the spray pattern twist the front ring.
English - 3