When You Receive Your Gemino; Using The Rollator; Adjusting The Rollator - Gemino 30 Parkinson Notice D'utilisation

MB4400 Gemino 30 Parkinson
When you receive your
Gemino
Assembly
1
The rollator is supplied complete as standard.
All you need to do is:
• Unfold the rollator.
• Set the pushing handles to the correct
height.
• Fit and adjust any accessories
• Check the brakes and adjust them if
necessary
Packaging
Take the packaging to an appropriate waste
reception centre. The plastic and cardboard
used in the packaging can be recycled.

Using the rollator

Driving brake
2
Always check that the brakes are working
before starting to use the rollator.
• Squeeze the brake handles to walk with the
rollator.
• Release the brake handles to brake the
rollator
• The brakes are activated when the brake
handles are released
• Do not push the rollator with the brakes in
the locked position. If you attempt to push
the rollator with force when the brakes are
locked or partly locked, this will result in
damage to the tyres and brakes, which in
turn can stop the brakes working properly.
• Do not use the rollator if the brakes are
defect.
Laser light for freezing
3
Incidents
The laser light shows a green line. The freezing
situation can be treated by using the laser light
as a visual cue to resume walking
• Push the button to activate the laser light.
• The laser light turns automatically off after
15 +/- 3 seconds.
Slow down brake
4
The rollator is equipped with slow down
brakes. To avoid the rollator "running away"
by unintentional movements or downhill.
The slow down brake gives resistance when
walking.
• Activate the slow down brake by pushing
the handle downwards. Deactivate by
pulling up. When the slow down brakes
are deactivated, the wheels rolls without
resistance.
Seat
5
• Always sit with your back towards the
direction of travel.
• A sling-style backrest for better support can
be purchased as an accessory.
Walking with the rollator
6
For the best support and the safest
movement, walk fully upright with the rollator
near your body. Tuck your bottom in. Look
forwards, not downwards.
Warning!
Do not push the rollator a long way in front
of your body. This can lead to falls and
incorrect loadings.
Do not lean or reach too far to the side
when using the rollator as the sideways
weight will make the rollator unstable.
Negotiating obstacles, tipping
7
bar
Step on the tipping bar to tip up the front
wheels of the rollator when you need to
negotiate kerbs, sills or other obstacles.
Side deflector
8
Gemino is equipped with a side deflector
which prevents the back wheel from catching
on protruding obstacles such as door frames
and corners.
Folding the rollator
9
The rollator locks automatically in the
completely folded position.
• Pull the strap to fold up the rollator. When
the rollator is completely folded, it locks and
you will hear a faint click.
Warning!
Be aware of the danger of trapping injuries
when folding and unfolding the rollator.
Be aware that the rollator cannot be
folded into a locked position for all height
adjustments! with the Parkinson pushbutton
housing mounted on the inner side.
Unfolding the rollator
9
The rollator locks automatically in the
completely open position.
• Pull the operating handles apart.
• Press the side bars down until you hear a
small click in the fully unfolded position.
• Before using the rollator, make sure that the
folding mechanism is locked in place.
Lifting and carrying the rollator
9
The lifting handles are most easily accessible
when the rollator is folded.
• Fold the rollator before lifting it, as this is the
best way to lift it and the easiest because of
the relation between weight and the lifting
handles.

Adjusting the rollator

Height of the pushing
10
handles
To achieve the correct pushing position and
avoid incorrect loadings, the pushing handles
must be adjusted so that the user walks
upright into the rollator and does not need to
bend his or her back while pushing.
• Lift the catch.
• Push or pull the pushing handle to the
correct height.
• Release the catch. The pushing handle will
now be automatically locked at the correct
height.
Memory function for correct
11
height of pushing handle
The memory function enables you to quickly
set the pushing handle back to the correct
height if the height has been changed during
transport etc.
• Before activating the memory function, you
must decide the correct height of the push
,
handles
• Loosen the screw
• Lift out the pushing handle.
• Turn the memory block
pull it right out.
• Position the block at the correct height. Now
the pushing handle cannot be positioned
higher than the point at which the memory
block has been set, but you can still push it
right down for transport.
• Tightly close the height adjustment catch
once you have positioned the pushing
handle correctly.
• Retighten the screw
12 Adjusting the brakes
• Loosen the locking nut
• Adjust the brake by screwing the cable
adjuster nut inwards or outwards.
• Test the brakes by releasing the brake
levers.
• The wheels should be completely locked
Adjusting slow down brake
13
resistance
• Turn the knob to adjust the resistance.
• Ensure to have the same resistance on both
wheels.
Adjusting the laser line
14
Position of the laser line can be adjusted.
• Loosen the screw
position until the laser line hit the desired
position.
• Tighten the screw.
English 17
using a 3 mm Allen key.
through 90° and
.
.
and adjust the laser