Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, damaged
mountings, and any other condition that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
•
Do not operate cordless tools in damp or wet locations or
in the rain. Following this rule will reduce the risk of
electric shock.
•
When servicing use only identical replacement part.
•
To reduce the risk of electric shock, this tool has a
polarized plug (one blade is wider than the other) and will
require the use of a polarized extension cord. The plug
will fit into a polarized extension cord only one way. If
the plug does not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a correct
polarized extension cord. A polarized extension cord will
require the use of a polarized wall outlet. This plug will
fit into the polarized wall outlet only one way. If the plug
does not fit fully into the wall outlet, reverse the plug. If
the plug still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the
equipment plug, extension cord receptacle, or extension
cord plug in any way.
•
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be used
for the gardening appliance. Receptacles are available
having built-in GFCI protection and may be used for this
measure of safety.
•
Warning – To reduce the risk of electric shock, use only
with an extension cord intended for outdoor use, such as
an extension cord of cord type SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
•
Disconnect Appliance – Remove appliance from power
source before storing, servicing, changing accessories
such as cutting line. Such preventive safety measures
reduce the risk of starting the tool accidentally.
•
Do not abuse the cord – Never carry the unit by the
extension cord or yank extension cord to disconnect unit.
Keep the cord clear of operator and obstacles at all times.
Do not expose cords to heat, oil, water, or sharp edges.
Do not handle plug with wet hands.
SAVE THESE INSTRUCTIONS
3
SYMBOLS ON THE MACHINE
Some of the following symbols can be used on this machine.
Please study them and learn their definition. Proper
interpretation of these symbols will let you operate the
machine better and safer.
Symbol
Explanation
V
Voltage
A
Current
Hz
Frequency (cycles per second)
English
Symbol
W
min
/min
4
RISK LEVELS
The following signal words and meanings are intended to
explain the levels of risk associated with this product.
SYM-
SIGNAL
BOL
DANGER
WARNING
CAUTION
5
Explanation
Power
Time
Revolutions, strokes, surface speed, or-
bits etc., per minute
Alternating Current
Double-insulated construction
Always wear safety glasses with side
shields marked to comply with ANSI
Z87.1 when you operate this machine.
Read and understand all instructions be-
fore you operate the machine, and follow
all warnings and safety instructions.
Precautions that involve your safety.
Do not expose the machine to rain or
moist conditions.
Keep all bystanders at least 15m away.
Do not install or use any type of blade on
the machine or displaying this symbol.
Thrown objects can ricochet and result in
personal injury or property damage.
Do not expose to rain or use in damp lo-
cations.
MEANING
Indicates an imminently haz-
ardous situation, which, if not
avoided, will result in death
or serious injury.
Indicates a potentially hazard-
ous situation, which, if not
avoided, could result in death
or serious injury.
Indicates a potentially hazard-
ous situation, which, if not
avoided, may result in minor
or moderate injury.
EN
Publicité
Table des Matières
