Removing/Inserting The Battery - Milwaukee FORCELOGIC M18 2778-20 Manuel De L'utilisateur

Copper
Industrial
Aluminum
Grounding
Copper
Aluminum
Overhead
ASCR
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
An incomplete or faulty crimp could cause a fire.
Use tool only with "U" dies and connectors for
which they are rated. Jaws, dies, and connectors
must be used in an approved combination to
achieve a successful operation. Improper combi-
nations can result in a faulty crimp. Electric shock,
fire, explosion, and property damage could occur.
Changing the Dies
Inspect dies and connectors before use. Only use prop-
erly matched dies and connectors for the crimping jaws.
Refer to Specifications for die/connector compatibility.
1. Remove the battery pack.
2. Snap the appropriate dies into each side of the
crimping jaws.
3. To remove, press the release button for each side of
the crimping jaws. Pull dies out from crimping jaws.
ONE-KEY™
To learn more about the ONE-KEY™ function-
ality for this tool, please reference the Quick
Start guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
Connector Capacity Matrix
Connector Type
Copper Splices
Copper Lugs
Copper "C" Taps
Aluminum Splices
Aluminum Lugs
Aluminum Pin Adapters
Aluminum "H" Taps
Ground Grid Connectors
Copper "E" Taps
Copper Tension Splice
Copper Lugs
Copper "H" Taps
Aluminum Tension Splice
Aluminum Stirrups
Aluminum Lugs
Aluminum Jumper Splice
Aluminum "H" Taps
ASCR One Piece Tension Splice
ASCR Two Piece Tension Splice
ASCR Stirrups
5/8" Service Entrance Connectors
840 Service Entrance Connectors
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready to
be configured via the ONE-KEY™ app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of arc flash,
WARNING
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken first.
Keep hands away from crimping jaws
while tool is in use. Fingers could be
crushed.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Before crimping:
• Inspect the jaws and dies for cracks or other dam-
age. Do not use damaged jaws or dies. Contact a
MILWAUKEE service facility.
• Ensure dies are properly installed.
• Jaws, dies, connectors, and cables must be used in
an APPROVED COMBINATION. Improper combi-
nations can result in a faulty crimp.
4
Capacity Range
#8 - 750 MCM
#8 - 750 MCM
#14sol - 500 MCM
#8 - 750 MCM
#8 - 750 MCM
#6 - 750 MCM
#8 - 500 MCM
#8 - 500 MCM
#8 - 500 MCM
#8sol - 500 MCM
1/0 - 500 MCM
#12 - 4/0
#6 - 587.5 MCM
#6 - 500 MCM
#4 - 556.5 MCM
#4 - 556.5 MCM
#8 - 500 MCM
#6 - 587.5
#4 - 556.5 MCM
#6 - 477
#10 - 1/0
1/0 - 4/0
Crimping