Accessories - DeWalt DCE151 Guide D'utilisation

English
Fig. F
2
The center position of the directional button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
Stripping a Cable End (Fig. A, G)
nOTE: Ensure cable has a straight, round end and remove
and debris or jacket remnants from the bushing before
beginning.
1. Determine cable type and size. Choose and attach the
appropriate bushing; refer to Choosing and Attaching
a Bushing.
2. Lift up and unfasten the depth stop tab
the depth stop to the desired strip length; retighten the
tab and press it flat agains the tool.
3. Set the directional button
4. Insert the cable end into the bushing opening.
nOTE: When working overhead, always confirm
workpiece is secure before stripping and be sure the
cable end does not create a hazard as it is removed from
the barrel.
5. Begin stripping by inserting the cable into the bushing
and align the end against the cutting blade that is
just inside the bushing (do not press the cable into or
past the blade prior to pulling the trigger). Depress the
trigger to rotate the stripping barrel while applying
pressure against the cable end feeding it further into the
stripping barrel, release the pressure against the cable
after blade start stripping the insulator.
nOTE: The LED worklight
illuminate when trigger is depressed. Refer
to Worklight.
if the blade gets stuck:
-
a. Release the trigger
b. Set the directional button
c. Depress the trigger to back the tool off of
the cable
d. Set the directional button to forward and
continue stripping. NOTE: ensure any partialy
stripped jacket is removed prior to continuing
the strip.
6. When the stripped cable reaches the depth stop, the
blade will automatically sever the casing evenly. If a
longer strip is desired adjust depth gauge appropriately
and strip the additional jacket off the cable
7. Remove from the cable from the barrel.
10
2
1
5 and adjust
2 to forward.
8 will automatically
2 to reverse
Fig. G
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.

Accessories


WARNING: Since accessories and bushings, other
than those offered or recommended by D
have not been tested with this product, use of such
accessories or bushings with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories and bushings should be
used with this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
For a complete and most up to date list of compatible
attachments and bushings visit www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
or a D WALT authorized service center. Always use
e
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
WALT,
e
WALT-
e
WALT Industrial
e