Fender RUMBLE 15 Mode D'emploi page 7

Connect a footswitch to the Rumble 75 to remotely enable
OVERDRIVE. Fender makes three footswitch pedals that will work
with the Rumble 75 (shown at right with part numbers). Any
generic single-button latching-type footswitch will work.
recommend the Fender LED FOOTSWITCH (P/N 0994052000) for
best performance. Contact your local Fender dealer to purchase
the Fender footswitch of your choice.
NOTE: If a footswitch is connected, the front panel switch will still
work, but it is possible for its position IN/OUT to become backwards
(i.e. IN=OFF), depending on the footswitch status. The Overdrive
light (LED) on the front panel will ALWAYS be correct, but the LED in
the footswitch may be incorrect. If using a footswitch with an LED,
keep the front panel switch in the OUT position to have the correct
status displayed on the footswitch LED.
Delta-Comp™ Limiter Delta-Comp™ Limiter
Rumble bass amplifiers are equipped with Fender's Delta-
Comp limiter to minimize power amp distortion and increase
sustain. Setting the VOLUME control to higher settings or playing
aggressively with hotter basses may result in a heavily compressed
sound with increased sustain. Using INPUT 2 or setting the
VOLUME control lower will provide a less compressed sound with
more dynamic range and increased touch-sensitivity.
MODEL: Rumble 15
POWER REQUIREMENT:
40W Max / 20W Typical
INPUT IMPEDANCES:
1MΩ (Input) / 10kΩ (Aux In)
PRE-AMP SENSITIVITY:
40mVrms
(Full power @ 100Hz, Volume at max, tone controls flat)
POWER AMP OUTPUT:
15W into 8Ω @ <0.1% THD, 100Hz
TONE CONTROLS: BASS: ±15dB @ 60Hz
MID: ±15dB @ 630Hz
TREBLE: ±15dB @ 6kHz
SHAPE FILTER:
N/A
LINE OUT:
N/A
HEADPHONE OUTPUT:
110mW into 32Ω/Channel
SPEAKERS:
One 8Ω, 8", Special Design,
Specifications are subject to change without notice. Visit www.fender.com for additional product information.
All manuals and user guides at all-guides.com
Optional Footswitch Optional Footswitch
We
Block Diagram Block Diagram
Specifications Specifications
Rumble 30
80W Max / 40W Typical
1MΩ (Input 1) / 136kΩ (Input 2) / 10kΩ (Aux In)
40mVrms (Input 1) / 80mVrms (Input 2)
30W into 8Ω @ <0.1% THD, 100Hz
BASS: ±15dB @ 60Hz
MID: ±15dB @ 630Hz
TREBLE: ±15dB @ 6kHz
N/A
N/A
280mW into 32Ω/Channel
One 8Ω, 10", Special Design,
fender.com fender.com
1. ECONOMY FOOTSWITCH — (P/N 0994049000)
Basic black one-button on/off footswitch
2. VINTAGE FOOTSWITCH — (P/N 0994054000)
Chrome one-button on/off footswitch.
3. LED FOOTSWITCH — (P/N 0994052000) Contemporary one-
button on/off footswitch with LED indicator.
NOTE: You must switch the Overdrive effect off
before connecting this footswitch to enable the
footswitch LED to operate properly.
Tilt-Back Cabinet Tilt-Back Cabinet
The tilt-back cabinet design of the Rumble 30 & 75 offers additional
tonal flexibility for your amplifier. Leaving the cabinet in the
upright position will enhance low-end bass response. Tilting the
cabinet back will direct midrange and treble frequencies upwards,
providing a clearer sound that may be easier to hear in small rooms
or rehearsal situations. Experiment with cabinet position to find
the best tone for your application.
Rumble 75
200W Max / 100W Typical
1MΩ (Input 1) / 136kΩ (Input 2) / 10kΩ (Aux In)
40mVrms (Input 1) / 80mVrms (Input 2)
75W into 8Ω @ <0.1% THD, 100Hz
BASS: ±15dB @ 80Hz
LOW MID: ±12dB @ 400Hz
HIGH MID: ±12dB @ 1.2kHz
TREBLE: ±15dB @ 10kHz
PUNCH: +7dB @ 170Hz, –12dB @ 50Hz
SCOOOP: +2dB @ 125Hz, –13dB @ 650Hz, +2.5dB @ 8kHz
+8.75dBU (into 600Ω), Maximum Output
280mW into 32Ω/Channel
One 8Ω, 12", Special Design,
7 7