Standard Accessories; Applications; Battery Removal/Installation - HIKOKI DV 14DJL Mode D'emploi

English

STANDARD ACCESSORIES

1 Plus driver bit (No. 2) .............................. 1
DV14DJL
2 Charger (UC18YKSL) ............................. 1
(2LEGK)
3 Battery (BSL1415 or BSL1815) .............. 2
DV18DJL
4 Plastic case ............................................ 1
(2LEGK)
5 Battery cover .......................................... 1
1 Plus driver bit (No. 2) .............................. 1
DV14DJL
2 Charger (UC18YKSL or UC18YFSL) ...... 1
(2LFRK)
3 Battery (BSL1425 or BSL1825) .............. 2
DV18DJL
(2LFGK)
4 Plastic case ............................................ 1
(2LFRK)
5 Battery cover .......................................... 1
1 Plus driver bit (No. 2) .............................. 1
DV18DJL
2 Plastic case ............................................ 1
(NNK)
Without charger, battery and battery cover.
1 Plus driver bit (No. 2) .............................. 1
DV18DJL
Without charger, battery, plastic case and
(NN)
battery cover.
Standard accessories are subject to change without notice.
The charger and battery supplied are diff erent depending on
the set specifi cation.
OPTIONAL ACCESSORIES (sold separately)
○ Battery
BSL1415S, BSL1415, BSL1425
BSL1815S, BSL1815, BSL1825
○ Hook
Optional accessories are subject to change without notice.
Before
charging
While
charging
Charging
Pilot lamp complete
(red)
Overheat
standby
Charging
impossible
10
Table 1
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5
Blinks seconds. (off for 0.5 seconds)
Lights continuously
Lights
Lights for 0.5 seconds. Does not light for 0.5
Blinks seconds. (off for 0.5 seconds)
Lights for 1 second. Does not light for 0.5
Blinks seconds. (off for 0.5 seconds)
Lights for 0.1 second. Does not light for 0.1
Flickers seconds. (off for 0.1 seconds)

APPLICATIONS

○ Drilling of brick and concrete block, etc.
○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
○ Drilling of various metals.
○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch (2 pcs.)
to remove the battery (See Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (See
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the
a receptacle, the pilot lamp will blink in red
(At 1-second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in Fig.
3.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the
pilot lamp will blink in red (At 1-second intervals).
(See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
plug of the charger
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Malfunction in the
battery or the charger
to