Hoover MULTI SENSOR Manuel D'utilisation page 10

GB
#.'465 51.76+105
The following codes may appear during using. [Fig. 16]
Fig. 16
Error Description
Outer Layer's Filter
cleaning Alert
Filter replacement
Alert
Filter not present or
NVGT JCU PQV DGGP
locked
Dust sensor
malfunctioning: no
signal from sensor or
output voltage exceeds
the limit value
Motor no speed
CO sensor
malfunctioning
ATTENTION: +H CP[ QH VJGUG HCKNWTGU RGTUKUV EQPVCEV [QWT NQECN *QQXGT TGRTGUGPVCVKXG &1 016 VT[ VQ FKUCUUGODNG VJG *2WTK GT D[ [QWTUGNH
6417$.'5*116+0)
The following is a list of commonly encountered problems and solutions.
If any of these problems persist contact your local Hoover representative.
The Fan does not work
(Control Panel / Display
.KIJVU QP
The Fan does not work
(Control Panel / Display
.KIJVU QHH
No Lights on Control Panel /
&KURNC[ (CP 9QTMKPI
$WVVQPU QP VJG EQPVTQN RCPGN
/ Display do not operate
Air Flow is Weak
#KT 2WTK GT KU QRGTCVKPI
loudly
10
Error Description
Alert on product Control
Panel / Display
Filter Cleaning button turns
yellow
Filter Cleaning button turns
yellow
Filter Cleaning button and Filter
Replacement button blink
/
/
CO sensor status lamp is on in
yellow
• Check the alert showing on the display or in the app.
• Check if there are any obstructions in the fan.
• Check if the H-Purifier is switched on.
• Check if the filter is incorrectly installed and locked.
• The Air Purifier may be in the ECO mode due to the good air quality. See "AUTO MODE [Fig. 6]"
• Check if the H-Purifier is plugged in and switched on.
• Check if there are any obstructions in the fan.
• Check if the lights have not been switched off by pressing the Light Control button on the control Panel
/ Display.
• %JGEM KH %JKNF NQEM JCU DGGP CEVKXCVGF D[ RTGUUKPI CPF JQNFKPI VJG %JKNF .QEM $WVVQP HQT  UGEU
• Check if the protective packaging has been removed from the filter.
• Check if there are any obstructions in the Air Intake Cover or Air outlet.
• Check the Filter staus on the Control Panel / Display or in App for clean or replace warning.
• Check if the H-Purifier is in sleep mode. The fan operates on reduced power in this mode.
• Check if there are any obstructions in the Air Outlet or the fan.
• %JGEM KH VJG *2WTKHKGT KU TWPPKPI KP /#: OQFG VJG CKT HNQY KU CV OCZKOWO RQYGT KP VJKU OQFG
Alert on APP
Filter cleaning Alert
Filter replacement Alert
(KNVGT PQV RTGUGPV QT NVGT JCU
not been locked
Dust sensor malfunctioning: no
signal from sensor or output
voltage exceeds the limit value
Motor no speed feedback
CO sensor malfunctioning
Error Solution
1.Follow the instructions in I/M to clean the Outer
Layer's Filter.
2.Reset the alert.
(QNNQY VJG KPUVTWEVKQPU KP +/ VQ TGRNCEG VJG NVGT
2.Reset the alert.
+H NVGT KU PQV RTGUGPV RWV KV DCEM
+H NVGT KU KP RQUKVKQP EJGEM YJGVJGT VJG (KNVGT
Tab has been switched to LOCK status.
Dust sensor failure or dust sensor wire has not
been connected well, please call service center
VQ Z
Motor failure or motor wire has not been
EQPPGEVGF YGNN RNGCUG ECNN UGTXKEG EGPVGT VQ Z
Alert: need call service.