Table des Matières
Publicité
10
| English
4. CONNECTION OF THE GARDEN HOSE TO THE
WATER INLET
Connect the garden hose adaptor(female cou-
pler) to the water inlet of the pressure washer and
then thread your garden hose(male end) into the
garden hose adaptor (Fig. 5).
OPERATION
WARNING: Dry running for more than 2 minutes
can lead to damage of the high-pressure pump. If
the appliance does not build up pressure within 2
minutes, switch the appliance off and proceed in
accordance with the instructions in Chapter "Trou-
bleshooting"
High pressure operation
CAUTION: Keep a distance of at least 30 cm when
using the jet for cleaning painted surfaces to avoid
damage.
CAUTION: Make sure the ON/OFF switch is set to
"OFF" and insert the plug into a properly installed
socket.
ATTENTION: The washer must be used on a se-
cure and stable surface in a standing, upright posi-
tion. Connect the product to the power and water
supply as described.Open the water supply. Hold
the spray gun with both hands.Direct the nozzle
of the chosen accessory away from you towards
the surface to be cleaned.Unlock the trigger and
press it until a constant amount of water flows
through the nozzle, to allow air trapped in the
hose to escape.Release the trigger.
Turn "ON" the switch "ON/OFF".
Hold the spray gun with both hands. Direct the
water jet to the object to be cleaned and press
the trigger.
WARNING: Beware of kickback when pressing the
trigger!
The factory pre-set pressure provides the best wa-
ter pressure and cleaning effect. If the pressure
must be lowered down, it can be adjusted follow-
ingthe below methods:
Gradually keep the surface to be cleaned further
away. The further the surface is, the lower the pres-
sure is applied.
TWIST NOZZLE TO ADJUST SPRAY ANGLE
Adjust the unloader handle by turning the unload-
er handle counterclockwise to get lower pressure.
After use, turn theunloader handle clockwise to get
back to its original position (Fig. 6).
OPERATION WITH DETERGENT
Detergent can only be added when the device is op-
erated in low pressure mode.
DANGER: When using detergents, the material
data safety sheet issued by the detergent manu-
facturer must be viewed, especially the instructions
regarding personal protective equipment.
Remove the cap of the clean detergent bottle.
Gently pull the onboard detergent tank out of its
storage position.
Fill the tank with detergent designed specifically
for use with pressure washers.
Push the detergent bottle with the opening point-
ing downwards into the connection for the hose
clean detergent.
RECOMMENDED CLEANING METHOD
Spray the detergent sparingly on the dry surface and
f
allow it to react, but not to dry.
Spray off loosened dirt with the high pressure Met.
f
AFTER THE OPERATION WITH DETERGENT
Remove the hose clean detergent bottle from
the intake and close it with the lid, then clean the
detergent injection system with clean water. To
achieve a complete cleaning job on the detergent
injection system, apply detergent hose on clean
water to make sprays until the remaining deter-
gent is cleaned out from the system. Factory of
the high pressure cleaner is not responsible for
the damage caused by detergent or any chemical
agent.
For storage, put the detergent bottle into the re-
tainer with the cap pointing up.
OPERATION WITH BREAKS
Release the lever of the trigger gun.
f
Lock the lever of the trigger gun.
f
Put the trigger gun with the spray lance into the
f
parking position.
During longer breaks(more than 5 minutes), also
f
turn the appliance off using the "ON/OFF" switch.
START
Check inlet hose for residues and clogs
f
Connect water supply and pump inlet with inlet hose
f
and make sure the hose is air tide.
Connect high pressure hose to pump outlet.
f
Turn on the water supply
f
Start the electrical motor while turning ON the "ON/
f
OFF" switch
Pull the spray gun trigger, starting to spray
f
Release the trigger and stop the water
f
Adjust spray pattern by changing nozzle.
f
STOP
Release the lever of the trigger gun.
f
Shut off water supply.
f
Turn off the appliance "ON/OFF".
f
Disconnect the mains plug from the socket.
f
Press the lever of the trigger gun to release any re-
f
maining pressure in the system.
Release the lever of the trigger gun.
f
Lock the lever of the trigger gun.
f
ATTENTION
When disconnecting the supply or high pressure
f
hose, warm water may leak from the connection
after operation.
FROST PROTECTION
WARNING
Appliance and accessories that are not completely
HPW 151i PRO
Publicité
Table des Matières
