Publicité
Liens rapides
Publicité
Manuels Connexes pour HP Color LaserJet 2500 Serie
Sommaire des Matières pour HP Color LaserJet 2500 Serie
- Page 1 ºосу hp color LaserJet 2500 series başlat...
- Page 2 HP could void the user’s authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules. For more regulatory information, see the HP Color LaserJet 2500 electronic user guide. Hewlett-Packard shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this information.
- Page 3 The 2500 model also includes a 250-sheet tray (tray 2). The 2500n model with the same features as the 2500L model: a 125-sheet multipurpose tray includes tray 2 and an HP Jetdirect 615n print server card. The 2500tn (tray 1), parallel and universal serial bus (USB) interface ports, a slot for model includes tray 2, an HP Jetdirect 615n print server card, and a an optional HP print server card, and 64 MB RAM.
- Page 4 742.9 mm (29.25 in) Prepare the location. Place the printer on a sturdy, level surface in a Regulate the environment. Do not place the printer in direct sunlight or well-ventilated area. Make sure there is enough space around the printer an area that has abrupt temperature and humidity changes.
- Page 5 Minimum system requirements. See the outside of the box in which the Check the package contents. 1) the printer; 2) a power cable; 3) a printer shipped, or see the Readme on the CD-ROM. CD-ROM (includes the user guide and printer software); 4) this getting started guide 5) an imaging drum;...
- Page 6 Locate the printer parts. 1) power switch; 2) top output bin; 3) control Understand the control panel. 1) print-cartridge lights, panel; 4) top cover; 5) tray 1; 6) tray 2 (2500, 2500n, and 2500tn models); button 3) imaging drum light 4) button OTATE AROUSEL...
- Page 7 Remove the packing materials. Remove all orange tape from the printer. Remove the shipping locks. Open tray 2 and tray 3 and remove the orange shipping lock inside each tray. Retirez les éléments de l'emballage. Retrait des rubans adhésifs Retirez les dispositifs de sécurité d'expédition. Ouvrez les bacs 2 et 3, oranges de l'imprimante.
- Page 8 Install tray 3. Place tray 3 in the location you want. Lift the printer, align it Adjust the guides on tray 3. Letter-size paper: 1) Pull the tray out of the with the pegs on tray 3, and lower the printer onto the tray. Note: Only one printer.
- Page 9 Load paper in tray 3. 1) Load the paper with the side to be printed face Adjust the guides on tray 2. 1) Pull the tray out of the printer. 2) Move down, top edge toward the front. 2) Make sure the paper is flat at all the blue width guides to match the paper size being loaded.
- Page 10 Load paper in tray 2. 1) Load the paper with the side to be printed face Load tray 1. 1) Open tray 1 and slide out the tray extender. 2) Slide the down, top edge toward the front. 2) Make sure the paper is flat at all width guides until they are slightly wider than the paper.
- Page 11 Connect the power cable and turn on the printer. 1) Connect the power Install the imaging drum. 1) Remove the imaging drum from its cable between the power connector on the back of the printer and an ac packaging. 2) Place the imaging drum on a firm surface and pull the outlet.
- Page 12 5) Remove the orange cover from the imaging drum. CAUTION: Do not 7) Align the white roller on the imaging drum with the green arrows inside touch the surface of the white roller or print-quality issues can occur. the printer. 6) Open the top cover of the printer.
- Page 13 8) Lower the imaging drum into the printer and press it firmly into place. Install the print cartridges. 1) Look inside the printer on the right to see which print-cartridge slot is in the access position. 2) Locate the color of print cartridge that matches the color of the slot and remove the print cartridge from its packaging.
- Page 14 3) Remove the orange cover from the print cartridge. 4) Place the print 5) Squeeze the blue release levers on the print cartridge, holding it with cartridge on a flat surface and pull the orange tab straight out to remove the roller facing you.
- Page 15 6) Close the top cover. When the green Go light begins blinking, press Bring the printer to the Ready state. Close the top cover. After 60 . Repeat this process (step 18) to install the other three seconds, the green Ready light turns on. OTATE AROUSEL print cartridges.
- Page 16 Print a Demo page. With the Ready light on, press to print a Demo Choose ONE of these installations. To connect directly for Windows®, page, which verifies that the printer works. Note: If the page does not go to step 22. To install for a network, go to step 23. If the “New Hardware print, reconnect the power cable.
- Page 17 To connect directly for Windows. 1) Place the CD-ROM in the CD-ROM 3) Click Finish. 4) Before you restart the computer, connect the cable drive. 2) When prompted, click Install Printer and follow the instructions. between the printer and the computer. You cannot connect parallel and (If the welcome screen does not open, click Start and then Run.
- Page 18 Install for a network. (Note: The 2500n and 2500tn have an HP Jetdirect Print an HP Jetdirect page. Make sure the Ready light is on. Press print server card for network connection.) For a 10/100 Base-T network, simultaneously to print a Configuration page, an...
- Page 19 Install the network software. 1) Place the CD-ROM in the CD-ROM Macintosh on the network. 1) Run the Installer and restart the computer. drive and follow the instructions. 2) Click Finish and restart the computer. OS 8.6 to 9.2x: From HD/Applications/Utilities, use the Apple Desktop 3) To set up a Macintosh computer to use the network printer, see the next Printer Utility to select this printer.
- Page 20 Plug and Play. If you connected a parallel or USB cable to a Windows Windows 2000 and XP: 1) Click Search. 2) On the Locate Driver Files computer before you installed software, the “New Hardware Found” screen, select the Specify a Location check box, clear all other check message appears when you turn on the computer.
- Page 21 3) Double-click Win95, and then double-click the folder for the driver you point to Settings, and click Printers. Double-click Add Printer and follow want (PCL 6, PCL 5e, or PS). (HP recommends the PCL 6 driver.) the instructions. When prompted for a manufacturer, click Have Disk. (Go 4) Finish the installation and go to step 27.
- Page 22 Mac OS 8.6 - 9.x Connect the printer directly to a Macintosh. Connect a USB cable OS 8.6 to 9.2x: 1) Run the Installer and restart. Run the Apple Desktop between the USB port on the printer and the USB port on the computer. Printer Utility from HD/Applications/Utilities.
- Page 23 Note: If installation fails, reinstall the software. If reinstallation fails, see the Readme, see the flyer that came in the printer box, or go to http://www.hp.com/support/clj2500 for help or more information. OS X : Démarrez l'utilitaire Print Center à partir de Test de l'installation du logiciel.
- Page 24 Congratulations! Your printer is ready to use. See the HP Color LaserJet 2500 Toolbox (Windows 98 and later), where you can open the user guide and use tools to solve problems. Note: You must have performed a complete software installation to use the Toolbox.
- Page 25 Mac OS X...
- Page 26 Mac OS 8.6 - 9.x...
- Page 35 HP Color LaserJet 2500L HP Color LaserJet 2500n HP Color LaserJet 2500tn HP Color LaserJet 2500 742.9 mm (29.25 in)