Johnson Outdoors MINN KOTA MKA-51 Guide D'installation

Support à dégagement rapide à commande électrique

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

®
Compatible with Minn Kota
and DeckHand 40.
Item /
Part #
Description
Assembly
A
2994936
BAG ASM, ES SLIDING QRB
Items 2-10
2
2223446
SCREW-1/4-20 X 2" PFH SS
4
2373484
SCREW-1/4-20 X 7/8 PFH SS
6
2263103
NUT-1/4-20 NYLOCK SS
8
2261713
WASHER-1/4 FLAT 18-8 SS
10
2371712
WASHER-FLAT 9/32 X 5/8 X 1/16
B
2771998
BOTTOM PLATE KIT, MKA-51 QRB
Items 12-16
12
2381958
PLATE-BOTTOM, QRB, MACH
14
2228413
CAM PUCK - MACHINED
16
2373428
SCREW-5/16-18 X 3/4" PFH SS
C
2771997
TOP PLATE KIT, MKA-51 QRB
Items 18-40
18
2381956
PLATE-TOP, QRB, MACH
20
2373611
DRAWBAR, ES QRB
22
2222716
SPRING,COMPRESSION OD.480
24
2373260
STOP, DRAW BAR
26
2383431
SCREW-1/4 X 3/4 TY AB PFH
28
2225110
PAD, URETHANE,QCK ATTACH
30
2381948
EXTRUSION BACKER, MACH QRB
32
2228415
CAM ARM, QCK ATTACH PLATE
34
2262635
PIN-ROLLER, S/S
36
2372623
PIN W/RING, QRB
38
2373650
LANYARD ELECTRIC STEER,QRB
40
2372644
PIN-ROLL, .093 x 5/8" SS
Not shown on Parts Diagram.
This part is included in an assembly and cannot be ordered individually.
TOOLS AND RESOURCES REQUIRED
• #3 Phillips Screw Driver
• Drill
MOUNTING CONSIDERATIONS
It is recommended that the motor be mounted as close to the
centerline or keel of the boat as possible. The motor must not
encounter any obstructions as it is lowered into the water or raised
into the boat when stowed and deployed. Make sure the motor rest is
positioned far enough beyond the edge of the boat. Make sure the area under
the mounting location is flat, clear to drill holes and install nuts and washers.
1 | minnkotamotors.com
Freshwater Electric-Steer Trolling Motor models, including the Ulterra™, Terrova
• 9/32" Drill Bit
• 7/16" Box End/Open End Wrench
MKA-51 ELECTRIC-STEER
QUICK RELEASE BRACKET
Qty.
1
6
6
C
C
12
6
6
1
38
38
1
1
1
1
1
1
1
1
2
B B
1
1
1
1
2 2
1
1
A A
1
NOTICE:
Images are a graphical representation and may
vary slightly from your motor.
®
, PowerDrive™, PowerDrive V2
20
20
22
22
24
24
28
28
30
30
40
40
12
12
6 6
8 8
10
10
• A second person to help with
the installation
©2020 Johnson Outdoors Marine Electronics, Inc.
1854051
18
18
26
26
36
36
34
34
32
32
14
14
16
16
4 4

Publicité

Table des Matières
loading

Sommaire des Matières pour Johnson Outdoors MINN KOTA MKA-51

  • Page 1 Make sure the motor rest is positioned far enough beyond the edge of the boat. Make sure the area under the mounting location is flat, clear to drill holes and install nuts and washers. 1 | minnkotamotors.com ©2020 Johnson Outdoors Marine Electronics, Inc.
  • Page 2: Operating

    The motor should be in the stowed position. Stowed Stowed NOTICE: A motor may weigh up to 65lbs. We recommend Deployed Deployed having a second person help with the installation. ©2020 Johnson Outdoors Marine Electronics, Inc. 2 | minnkotamotors.com...
  • Page 3 Cam Lever will mount on the same end the Power Cord exits the base of the Mount. NOTICE: Bottom Plate Bottom Plate The Cam Lever will only open and close in one direction. Cam Lever Cam Lever ©2020 Johnson Outdoors Marine Electronics, Inc. 3 | minnkotamotors.com...
  • Page 4 Base Extrusion Base Extrusion Phillips screwdriver. Two of these screws will be Left Sideplate Left Sideplate located on each side of the mount. Right Sideplate Right Sideplate Sideplate Screw Sideplate Screw ©2020 Johnson Outdoors Marine Electronics, Inc. 4 | minnkotamotors.com...
  • Page 5 (Item #10) and a 1/4-20 Nylock Nut (Item #6). Outboard Outboard Top Plate Top Plate Stainless Stainless Steel Screw Steel Screw Inboard Inboard Mounting Mounting Holes Holes Top Plate Top Plate Inboard Inboard ©2020 Johnson Outdoors Marine Electronics, Inc. 5 | minnkotamotors.com...
  • Page 6 Do not deploy the motor until it is fully mounted to the boat. Illustrations are for reference only. Deploying your motor before it is mounted to the boat may cause injury. Extension Extension Damper Pins Damper Pins E-clips E-clips Damper Damper ©2020 Johnson Outdoors Marine Electronics, Inc. 6 | minnkotamotors.com...
  • Page 7 Washers up on the Stainless Steel Screw, so the Clipped Washer will sit on top of the Base Extrusion. Base Base Clipped Clipped Extrusion Extrusion Top Plate Top Plate Washer Washer ©2020 Johnson Outdoors Marine Electronics, Inc. 7 | minnkotamotors.com...
  • Page 8 Replace the Left Sideplate. Replace the four sideplate Screws using a #2 or #3 Phillips Screw Driver. Screw Screw Right Sideplate Right Sideplate Left Sideplate Left Sideplate Screw Screw Screw Screw Screw Screw ©2020 Johnson Outdoors Marine Electronics, Inc. 8 | minnkotamotors.com...
  • Page 9 Boat Boat Plate and Motor from the Bottom Plate. Top Plate Top Plate Cam Lever Cam Lever Inboard Inboard Inboard Inboard Bottom Plate Bottom Plate Markings Markings Markings Markings Markings Markings ©2020 Johnson Outdoors Marine Electronics, Inc. 9 | minnkotamotors.com...
  • Page 10 Place a Flat Washer (Item #8) and then a Nylock Flat Washer Flat Washer Nut (Item #6) at the end of each bolt as shown and tighten with the 7/16” Box End Wrench. Make sure all hardware is secure. ©2020 Johnson Outdoors Marine Electronics, Inc. 10 | minnkotamotors.com...
  • Page 11: Completing The Installation

    Minn Kota Consumer & Technical Service 121 Power Drive Johnson Outdoors Marine Electronics, Inc. Mankato, MN 56001 PO Box 8129 Phone (800) 227-6433 ©2020 Johnson Outdoors Marine Electronics, Inc. minnkotamotors.com Mankato, MN 56001 Fax (800) 527-4464 All rights reserved. Part #2377169...
  • Page 12: Support À Dégagement Rapide Àcommande Électrique Mka

    • Tournevis cruciforme nº 3 • Clé polygonale/ouverte de 7/16 po • Une deuxième personne pour vous • Perceuse (11,1 mm) aider avec l’installation • Mèche de 9/32 po (7,1 mm) ©2020 Johnson Outdoors Marine Electronics, Inc. 12 | minnkotamotors.com...
  • Page 13 Pour une liste complète des moteurs compatibles avec le MKA-51, veuillez consulter le site Web minnkotamotors.com. En-bord En-bord En-bord En-bord En-bord En-bord En-bord En-bord PowerDrive, PowerDrive, Ulterra Ulterra Terrova Terrova DeckHand 40 DeckHand 40 PowerDrive V2 PowerDrive V2 ©2020 Johnson Outdoors Marine Electronics, Inc. 13 | minnkotamotors.com...
  • Page 14: Installation De La Plaque Supérieure Sur Un Modèle Terrova, Powerdrive Ou Powerdrive V2

    Vis de plaque latérale Vis de plaque latérale Trous de montage Trous de montage Extrusion de Extrusion de la base la base Plaque latérale droite Plaque latérale droite ©2020 Johnson Outdoors Marine Electronics, Inc. 14 | minnkotamotors.com...
  • Page 15: Article(S) Requis

    à prévenir qu’elles grippent. avec les écrous Nylock. Serrez les écrous Nylock avec la clé polygonale ou ouverte de 7/16 po (11,11 mm). Assurez-vous que toute la quincaillerie est bien fixée. ©2020 Johnson Outdoors Marine Electronics, Inc. 15 | minnkotamotors.com...
  • Page 16 3. Deux de ces gauche gauche vis seront situées de chaque côté du support. Vis de plaque latérale Vis de plaque latérale Plaque latérale droite Plaque latérale droite ©2020 Johnson Outdoors Marine Electronics, Inc. 16 | minnkotamotors.com...
  • Page 17: Installation De La Plaque Supérieure Sur Un Deckhand

    (6,35-20 mm) (article nº 6). Hors-bord Hors-bord Vis en acier Vis en acier inoxydable inoxydable En-bord En-bord Trous de Trous de montage montage Plaque Plaque supérieure supérieure En-bord En-bord ©2020 Johnson Outdoors Marine Electronics, Inc. 17 | minnkotamotors.com...
  • Page 18: Installation De La Plaque Supérieure Sur Un Ulterra

    Les illustrations sont à titre de Serre-câbles Serre-câbles Prolongation de Prolongation de d’amortisseur d’amortisseur l’amortisseur l’amortisseur référence seulement. Le déploiement de votre moteur avant l’installation au bateau pourrait entraîner des blessures. ©2020 Johnson Outdoors Marine Electronics, Inc. 18 | minnkotamotors.com...
  • Page 19 Extrusion Extrusion Rondelle Rondelle de la base de la base taillée taillée Plaque supérieure Plaque supérieure ©2020 Johnson Outdoors Marine Electronics, Inc. 19 | minnkotamotors.com...
  • Page 20 Replacez la plaque latérale gauche. Replacez les quatre vis de la plaque latérale en utilisant un tournevis cruciforme nº 2 ou nº 3. Plaque latérale Plaque latérale Plaque latérale Plaque latérale droite droite gauche gauche ©2020 Johnson Outdoors Marine Electronics, Inc. 20 | minnkotamotors.com...
  • Page 21: Installation De La Plaque Inférieure Sur L'étrave

    Plaque supérieure Plaque supérieure Levier à came Levier à came En-bord En-bord En-bord En-bord Plaque Plaque inférieure inférieure Marques Marques Marques Marques Étrave Étrave Goupille Goupille Marques Marques ©2020 Johnson Outdoors Marine Electronics, Inc. 21 | minnkotamotors.com...
  • Page 22 écrou Nylock (article nº 6) à l’extrémité de chaque boulon, selon l’illustration, et serrez avec une clé polygonale de 7/16 po (11,11 mm). Assurez-vous que toute la quincaillerie est bien fixée. ©2020 Johnson Outdoors Marine Electronics, Inc. 22 | minnkotamotors.com...
  • Page 23: Terminer L'installation

    Minn Kota Consumer & Technical Service 121 Power Drive Johnson Outdoors Marine Electronics, Inc. Mankato, MN 56001 PO Box 8129 Phone (800) 227-6433 ©2020 Johnson Outdoors Marine Electronics, Inc. minnkotamotors.com Mankato, MN 56001 Fax (800) 527-4464 All rights reserved. Part #2377169...

Table des Matières