Installation; Safety; General Safety Instructions; Instructions, Standards And Regulations - Stiebel Eltron DHE 18 SLi 25 A Instructions D'utilisation Et De Montage

Chauffe-eau instantané à régulation entièrement électronique
Masquer les pouces Voir aussi pour DHE 18 SLi 25 A:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 42

INSTALLATION

Safety

INSTALLATION
7.
Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
7.1

General safety instructions

We guarantee trouble-free function and operational reliability
only if the original accessories and spare parts intended for the
appliance are used.
Material damage
!
Observe the maximum inlet temperature. The appliance
can be damaged by higher temperatures. You can limit
the maximum inlet temperature by installing a central
thermostatic valve (see chapter "Appliance description /

Accessories").

7.2

Instructions, standards and regulations

Note
Observe all applicable national and local instructions and
regulations, e.g. DIN 1988 / DIN EN 806 in Germany.
- The protection rating IP 25 (hoseproof) can only be ensured
with a correctly fitted cable grommet.
- The specific electrical resistance of the water must not fall
below that stated on the type plate. In a linked water net-
work, observe the lowest electrical water resistance (see
chapter "Specification / Application areas"). Your water
supply utility will advise you of the specific electrical water
resistance or conductivity.
8.

Appliance description

8.1

Standard delivery

Delivered with the appliance:
- Mounting bracket
- Installation template
- 2 twin connectors
- Cross-piece
- Tee
- Flat gaskets
- Strainer
- Plastic profile washer
- Plastic connection pieces / installation aid
- Cover and back panel guides
28
|DHE SLi
8.2
Accessories
Remote controls
- FFB 1 SL - Wireless remote control
Control from two locations
- FFB 2 SL - Wireless remote control
Wireless remote control unit as extension of the FFB 1 SL
- FB 1 SL - Hardwired remote control
Control only with remote control unit, suitable for self-sup-
porting installation
Taps/valves
- MEKD - kitchen pressure tap
- MEBD - bath pressure tap
Plug G ½ A
The plugs are required if you use pressure taps for finished walls
other than the ones recommended in the accessories.
Installation set for finished walls
- Solder fitting - copper pipe for solder connection Ø 12 mm
- Compression fitting - copper pipe
- Compression fitting - plastic pipe (suitable for Viega: San-
fix-Plus or Sanfix-Fosta)
Universal mounting frame
Mounting frame with electrical connections.
Pipe assembly for undersink appliances
This assembly for undersink installation is required if you need to
have the water connections (G ⅜ A) above the appliance.
Pipe assembly for offset installation
This pipe assembly with pipe bends is required if you need to
have the appliance vertically offset against the water connection
by approx. 90 mm downwards.
Pipe assembly for replacing a gas water heater
This pipe assembly is required if the installation has existing gas
water heater connections (cold water connection on the left and
DHW connection on the right).
Pipe assembly DHB water plug-in couplings
2 water plug-in couplings allow the appliance to be connected to
the available water plug-in connections of a DHB.
Load shedding relay (LR 1-A)
The load shedding relay which needs to be installed in the dis-
tribution board provides priority control for the instantaneous
water heater when operating, for example, electric storage heat-
ers simultaneously.
ZTA 3/4 - central thermostatic valve
Thermostatic valve for central premixing, for example for an in-
stantaneous water heater with a solar thermal system.
www.stiebel-eltron.com

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dhe 18 sliDhe 21 sliDhe 24 sliDhe 27 sli

Table des Matières