Introducing The Product; Description Of The Product; Technical Data; Preliminary Checks - Key Automation SUN4024 Instructions Et Avertissements Pour L'installation Et L'usage

2 - INTRODUCING THE PRODUCT

2.1 - Description of the product

The gear motor SUN is intended to be installed within systems for
the automation of sliding gates. The SUN gear motors have been
designed to automate sliding gates within the weight limits indicated
2.2 - Model and technical characteristics
Code
SUN4024
SUN4224
SUN7024/SUN7024M*
SUN7224
SUN11024/SUN11024M*
SUN52
SUN82
SUN122
SUN5024F
* magnetic limit switches

TECHNICAL DATA

MODELS
TECHNICAL SPEC.
Speed cm/s
Torque Nm
Working cycle %
Control unit
Vac
Power supply
(Vdc)
Absorption A
Engine power W
Capacitor µF
Thermoprotection °C
Integrated lights
Degree of protection IP
Dimensions (L-P-H) mm
Weight Kg
Operating temperat. °C
Leaves max weight Kg
Sound emission level dB(A)

3 - PRELIMINARY CHECKS

Before installing this product, verify and check the following steps:
- Check that the gate or door are suitable for automation
- The weight and size of the gate or door must be within the maxi-
mum permissible operating limits
- Check the presence and strength of the security mechanical stops
of the gate or door
- Check that the mounting area of the product is not subject to flood-
ing
- Conditions of high acidity or salinity or proximity to heat sources
could cause malfunction of the product
- Extreme weather conditions (for example the presence of snow,
ice, high temperature range, high temperatures) may increase the
friction and therefore the force required for the handling and initial
starting point may be higher than under normal conditions.
Description
24 Vdc gear motor with mechanical limit switches, gate maximum weight 400 kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 400 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 700 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 700 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 1100 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 500 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 800 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 1200 Kg
24 Vac gear motor with magnetic limit switches, gate maximum weight 500 Kg
SUN4024 SUN4224 SUN7024/
SUN7024M SUN7224
21 21 25
12 12 26
50 50 80
14A CT10224 14A
230(24) 230(24) 230(24)
1,1 1,1 1,5
250 250 345
- - -
- - -
SI - SI
44 44 44
330-210- 330-210- 330-210-
300 300 300
12 12 12,5
-20+55 -20+55 -20+55
400 400 700
≤ 70 ≤ 70 ≤ 70
in the technical specifications table.
The use of gear motors for applications which differ from those
indicated above is prohibited.
SUN11024/
SUN52
SUN11024M
25 20
26 38
80 80
CT10224 14A CT102B
230(24) 230(24) 230
1,5 1,3 1,3
345 300 300
- - 12,5
- - 150
- SI
44 44
330-210- 330-210- 330-210-
300 300 300
12,5 13 15,5
-20+55 -20+55 -20+55
700 1100 500
≤ 70 ≤ 70 ≤ 70
- Check that the manual operation of gate or door is smooth and
friction-free and there is no risk of derailment of the same
- Check that the gate or door are in equilibrium and stationary if left
in any position
- Check that the power line to supply the product is equipped with
proper grounding safety and protected by a magnetothermal and
differential security device
- Provide the power system with a disconnecting device with a gap
of contacts enabling full disconnection under the conditions dictated
by the overvoltage category III.
- Ensure that all materials used for the installation comply with cur-
rent regulations
SUN82 SUN122 SUN5024F
16 16 16
16 23 35
30 30 30
CT102B CT102B
230 230
1,9 2,6
450 600
16 20
150 150
- - -
44 44 44
330-210- 330-210-
300 300
16 16,5
-20+55 -20+55
800 1200
≤ 70 ≤ 70
EN
40
23
70
14A
230(24)
1,5
345
-
-
SI
44
330-210-
300
12,5
-20+55
500
≤ 70
9