Remaining Hazards; Dust Emission; Content Of Delivery; Technical Data - Jet JTS-700S Mode D'emploi

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving sawblade in the work area
can cause injury.
Broken saw blades can cause injuries.
Thrown workpieces can lead to injury
Tipping of the workpiece due to
insufficient support can lead to injury.
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.
4. Machine specifications

4.1 Technical data

JTS-700S:
Machine Table 685x380 mm
Rear extension table 500x380mm
Right extension table 685x630mm
Sliding table size 700x315(415)mm
Max. travel of sliding table
Max. length of cut
Sawblade diameter max 250 mm
Blade bore diameter
Blade speed n 4200 rpm
0
Cutting height at 90°/45° 82/57 mm
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains 230V ~1/N/PE 50Hz
Motor output power 2,2kW (3HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Motor output power 3,7 kW (5 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection
All manuals and user guides at all-guides.com
JTS-700L:
Machine Table
Rear extension table
Right extension table
Sliding table size
Max. travel of sliding table
Max. length of cut
Sawblade diameter
Blade bore diameter
Blade speed n
0
Cutting height at 90°/45°
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains
Motor output power
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains
Motor output power 3,7 kW (5 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN
1807:1999 (Inspection tolerance 4 dB)
Workpiece plywood 16mm:
T=16mm, L=800mm, moisture 8,5%
Acoustic power level (acc. EN 3746):
Idling
Operating
Acoustic pressure level (EN 11202):
820mm
Idling
700mm
Operating
The specified values are emission
30 mm
levels and are not necessarily to be
seen as safe operating levels.
Although there is a correlation
between emission and imission levels,
90°- 45°
these do not constitute a basis for
810 mm
determining the necessity of additional
100mm
safety measures. Workplace
200 kg
conditions which could influence the
noise imission level include the
duration of resonance, spatial
particulars, other noise sources etc.
13 A
For example, the number of machines
and other work being performed. The
16A
permissible workplace levels can vary
from country to country.
This information is intended to allow
8 A
the user to make a better estimation
of the hazards and risks involved.
16A

4.3 Dust emission

The circular saw JTS-700S/ 700L has
685x380 mm
been dust emission inspected.
500x380mm
685x630mm
At an air velocity of 20m/sec on the
dust port dia 100mm:
1000x315(415)mm
1120mm
Vacuum pressure
1000mm
Volume flow
max 250 mm
The TRK-value of 2 mg/m
30 mm
been exceeded.
4200 rpm
82/57 mm
90°- 45°

4.4 Content of delivery

810 mm
Sliding table
Mitre fence
100mm
200 kg Rear extension table
Right extension table
230V ~1/N/PE 50Hz
Rip fence with dual fence profile
2,2kW (3HP) S1
Rip fence support rail
13 A
Saw guard
Sawblade 250mm
16A
Dust connection hose and Y-adapter
Push stick
400V ~3/PE 50Hz
Operating tools
Assembly bag
8 A
Operating manual
Spare parts list
16A
5. Transport and start up

5.1 Transport and installation

The machine will be delivered on a
crate.
Attention:
Do not remove the motor transport
98,0 dB (A)
lock before the machine has been set
101,6 dB (A)
in place.
Do not operate the hand wheels.
84,0 dB (A)
Use a forklift or lifting straps to lift the
88,2 dB (A)
machine off the pallet.
Warning:
The machine weight is 240 kg.
Assure the sufficient load capacity
and proper condition of your lifting
devices.
Never step underneath suspended
loads.
For transport to the desired location
use a forklift or hand trolley. Make
sure the machine does not tip or fall
off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
5
850Pa
565 m³/h
3
has not