Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet JSS-354 Mode D'emploi

Insure that the workpiece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Never cut pieces that are too small.
During cutting operation the
workpiece must firmly be pressed
against the table surface.
Do not perform any operation
freehand.
Remove cut and jammed workpieces
only when motor is turned off and the
machine is at a complete standstill.
Do not reach under the scroll saw
table when the motor is running.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
work place switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not force the power tool.
It will do a better and safer job and
give you much better service if it is
used at the rate for which it was
designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
Remove defective saw blades
immediately.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving saw blade in the work
area can cause injury.
Broken saw blades can cause injuries.
Thrown workpieces can lead to injury
Wood chips and sawdust can be
health hazards.
Be sure to wear personal protection
gear such as safety goggles ear- and
dust protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.
4 4

4. Machine specifications

4.1 Technical data

Saw blade length, pin type
Blade stroke
Max cutting height at 90°
Table size
Table tilt 45°left/10°right
Throat
Dust port diameter (D/d)
Overall (LxWxH) 640x290x390mm
Weight
Mains 230V ~1L/N/PE 50Hz
Motor power
Reference current
Extension cord H05VV-F 3G1mm²
Installation fuse protection
JSS-354
2 Blade speeds 700 / 1400 spm
JSS-354V
Variable blade speed 400~1400 spm

4.2 Noise emission

(Inspection tolerance 4 dB)
Acoustic power level
(according EN ISO 3746):
Idling LwA 79,2 dB(A)
Acoustic pressure level
(according EN ISO 11202):
Idling LpA 72,1 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels. This
information is intended to allow the
user to make a better estimation of
the hazards and risks involved.
4.3 Content of delivery
1 Scroll saw
1 Transparent blade guard
1 Air blower
1 Allen key 3mm (5)
1 Allen key 2,5mm (4)
2 Blade clamps (6)
Sets of saw blades (1-3)
Operating manual
Spare parts list
130mm
20mm
60mm
460x230mm
460mm
40/36mm
27 kg
120W
0,7 A
10A