Publicité
Les langues disponibles
Les langues disponibles
15
14
13
Put the bottle cover on the fan assembly. Wait 20 minutes for the wick to become fully
saturated, then proceed to step 14.
14
Plug in your unit and press the power knob power-of . Set your desired fan speed by turning
the power knob. Your Alliance has four fan speeds that are displayed by F1 (the lowest
speed) through F4 (the highest speed).
Note: On higher speeds, the Alliance puts out a tremendous amount of humidity, so it's louder on these levels. Most of our
customers liken it to the sound of a box fan. Rest assured there is nothing wrong with your unit, it's just working very hard to put
out much-needed humidity.
15
Turn the humidity control knob to set your humidity level from 25% to 65%. The
humidistat on your cord will read your home's humidity and turn your fan off when the
set level is reached. When set to 65%, your unit will run continuously.
5
11
Note the raised lettering on your bottle
that says FRONT and REAR. Put the
water bottle in the base with this lettering facing
the fan, the front of the bottle facing the front of
the Alliance, and the cap facing down.
12
Let the bottle drain completely into the
cabinet, then remove the bottle and refill
it. Put the bottle back into the cabinet. Filled twice
like this, your Alliance holds 5.4 gallons of water.
About water additives:
Do not use essential oils in your Alliance.
•
Do not use water softeners.
•
We recommend our Essick Air Bacteriostat to help inhibit
•
mold growth.
ABOUT THE CODES
F
– The F code means your unit is empty and needs to be FILLED with water.
CL
– Your CONTROLS ARE LOCKED on the current setting. Activate the control lock by holding the power button for five
seconds, until CL appears. Your Alliance will lock on the current fan and humidity settings. Release the lock by pressing the
power button again for five seconds until the display flashes CL three times, letting you know the lock is off.
CF
– The CF code triggers after 720 hours of use and means it's time to CHECK YOUR FILTER (wick). Unplug your unit and
check your wick. If your wick is still in good shape, simply clear the code by plugging your humidifier back in. If your wick
needs replacing, install a new 1045 Super Wick®.
HOW TO CLEAN YOUR ALLIANCE
Regular cleaning is important for preventing mold, mildew, and other bacterial growth
in your humidifier. It also keeps your Alliance working its best.
1. Let the unit run until it's empty, then turn it off and unplug it.
2. Remove everything from the cabinet. Throw your wick away if it is time to replace it.
Otherwise, put it in a sink while you finish cleaning your Alliance.
3. Pour out any remaining water from the cabinet and water bottle.
4. Fill the cabinet half-full with water and add 1 cup of white vinegar. Let sit for 20 minutes.To
disinfect, replace the vinegar with 1 teaspoon of bleach. Do not mix vinegar and bleach.
5. Fill the water bottle half-full with water and add 1 cup of white vinegar. Put the cap back
on, shake the bottle gently, then let sit for 20 minutes. To disinfect, replace the vinegar
with 1 teaspoon of bleach in each bottle.
6. After 20 minutes, empty the cabinet and bottle.
7. Dampen a sponge with white vinegar and wipe down the cabinet, bottle, and float rod
(rinse the Styrofoam float with water only). Rinse everything thoroughly. To disinfect,
replace the vinegar with bleach. Wipe down the bottle, float rod, and cabinet interior
only.
8. Wipe everything dry and replace the wick, if needed. Then reassemble.
When storing your Alliance, discard the used wick and disinfect the unit using
the directions above. Dry the unit thoroughly, and store in a temperature-regulated
area. Do not install a new wick until you are ready to use your humidifier again.
6
Publicité
