Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
eng
Use of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal
objects like paper clips, coins, keys, nails, screws, or other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery,
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejec-
ted from the battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of 5°C/40°F or 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste.
Take them to an authorised ROLLER after-sales service facility or
to a reputed waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
b) Comply with maintenance instructions and instructions on tool
replacements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised ROLLER after-sales service
facility in case of damage. Check extension cable regularly and
replace it when damaged.
Specific Safety Instructions
Use only electrical plugs with shockproof socket. Check the earth
•
(ground) connection of the plug.
Use only extension leads with shockproof socket.
•
Never use the drive unit without the PRCD fault-current safety switch
•
supplied.
Always check the PRCD fault-current safety switch for correct functio-
•
ning before starting a drilling operation (see 3.).
When drilling, hold the drive unit only by the insulated handles provided
•
for the purpose.
Ensure that no water is allowed to get into the drive unit during operation.
•
If you detect a leak in any part of the water supply system, shut the ma-
•
chine down immediately and repair the fault. Water pressure should not
exceed 4 bar.
Have the core drilling operations marked out by the person in charge of
•
operations.
The statics must not be negatively influenced in any way by the core
•
drilling work, consult site management or the engineer engaged in
statical calculations if necessary.
Take care not to damage gas, water, power and other conduits in the
•
area of the drilling operation. Drain or shut off these conduits as required.
Block off the working area and place warning signs on both sides of the
•
wall when drilling through from one side to the other.
Take appropriate precautions to ensure that, in the event of a drilling
•
core dropping out, no personal injury or material damage will result.
When handling hollow components, check the flow route of the diluted
•
soluble oil in order to prevent damage (e.g. from frost).
Note that the diamond core drilling crowns can become blocked at any
•
time. During manually controlled core drilling, there is a danger of the
drive unit jumping out of your hands.
Do not attempt to work above shoulder height with electrically-driven
•
core drilling machines.
1. Technical specifications
1.1. Article numbers
ROLLER'S Centro S1 drive unit
ROLLER'S Centro S3 drive unit
Holder-up
ROLLER'S drill upright S
ROLLER'S drill upright D
Universal diamond core drilling crowns
ROLLER'S UDKB 32 x 420 x UNC 1
ROLLER'S UDKB 42 x 420 x UNC 1
ROLLER'S UDKB 52 x 420 x UNC 1
ROLLER'S UDKB 62 x 420 x UNC 1
ROLLER'S UDKB 72 x 420 x UNC 1
All manuals and user guides at all-guides.com
180000
180001
180050
182000
182001
1
/
181010
4
1
/
181015
4
1
/
181020
4
1
/
181025
4
1
/
181030
4
ROLLER'S UDKB 82 x 420 x UNC 1
ROLLER'S UDKB 92 x 420 x UNC 1
ROLLER'S UDKB 102 x 420 x UNC 1
ROLLER'S UDKB 112 x 420 x UNC 1
ROLLER'S UDKB 122 x 420 x UNC 1
ROLLER'S UDKB 132 x 420 x UNC 1
ROLLER'S UDKB 152 x 420 x UNC 1
ROLLER'S UDKB 162 x 420 x UNC 1
Expansion anchor M12 (masonry), 10 units
Knock-in anchor M12 (concrete), 50 units
Flattener for knock-in anchor M12
Fast-tightening nut set (art. no. 079007, 079008, 079009)
Knurled threaded rod M12 x 65
Fast-tightening nut
Washer
Tapping tool G
1
/
for Ø 8 mm drill
2
Single-ended wrench SW 19
Single-ended wrench SW 30
Single-ended wrench SW 32
Single-ended wrench SW 41
Hexagon socket head wrench SW 3
Hexagon socket head wrench SW 6
Suction rotor for dust extraction
Adapter G
1
/
male – UNC 1
2
Annular core bit extension 200 mm x UNC 1
Sharpening stone
1.2. Drilling depth
Useful drilling depth of the ROLLER'S Universal
diamond core drilling crown
Deeper core-drilling operations can be carried out with the annular
core bit extension (see 3.7).
1.3. Drilling range
Centro S1
Core drilling operations
in steel-reinforced
concrete
Ø 20 – 102 (132) mm Ø 20 – 152 mm
Core-drilling operations
in masonry
Ø 20 – 152 mm
Annular-bit connection
thread
Drill collar diameter
1.4. Turning speeds
Idling
830 rpm
At rated load
580 rpm
1.5. Electrical specifications
Supply voltage
Power consumption
Rated current capacity
Fuse protection (mains network)
Supply voltage
Power consumption
Rated current capacity
Fuse protection (mains network)
Fault-current safety switch, PRCD
(Portable Residual Current Device)
with low-voltage release
1.6. Dimensions (L x W x H)
ROLLER'S Centro S1
drive unit
ROLLER'S Centro S3
drive unit
ROLLER'S drill upright S
ROLLER'S drill upright D
1.7. Weights
ROLLER'S Centro S1 drive unit
ROLLER'S Centro S3 drive unit
ROLLER'S drill upright S
ROLLER'S drill upright D
1
/
4
1
/
4
1
/
4
1
/
4
1
/
4
1
/
4
1
/
4
1
/
4
1
/
male
4
1
/
4
Centro S3
Ø 20 – 252 mm
UNC 1
1
/
male, G
1
/
female
4
2
60 mm
750, 1800, 2500 rpm
530, 1280, 1780 rpm
Centro S1
Centro S3
230 V, 50/60 Hz
1800 W
2200 W
8.4 A
10 A
10 A (B)
16 A (B)
115 V, 50/60 Hz
1700 W
2050 W
15 A
18 A
20 A
25 A
10 mA
10 mA
460 x 160 x 100 mm (18.1"×6.3"×3.9")
540 x 160 x 100 mm (21.3"×6.3"×3.9")
400 x 200 x 775 mm (15.7"×7.9"×30.5")
440 x 230 x 935 mm (17.3"×9.1"×36.8")
5.2 kg (11.5 lb)
7.4 kg (16.3 lb)
9.7 kg (21.4 lb)
12.8 kg (28.2 lb)
eng
181035
181040
181045
181050
181055
181060
181065
181070
079006
079005
182050
079010
079008
079009
079007
180150
079000
079001
079002
079003
079011
079004
180160
180052
180155
079012
420 mm
Publicité
Table des Matières
