Available Accessories - RFC L-PAD 12C Manuel Utilisateur

AVAILABLE ACCESSORIES

- RCF mixing consoles PLAYER Card: USB stick based MP3 Player Card – Max. capacity: 32 GB (p.n. 133 60 287)
- RCF mixing consoles recorder card: USB flash drive based MP3 player/recorder card ‑ Max. capacity: 32 GB (p.n. 133 60 288)
- RCF mixing consoles Bluetooth card: Bluetooth connection card. This card allows to play your music playlist from Smartphone, Tablet or any Bluetooth
device. (p.n. 133 60 289)
MOUNT ACCESSORIES
- Rack ears (RCF Part Number: 133 60 292)
OPTIONAL CARDS
RCF mixing consoles OPTIONAL CARDS Installation and use
With the help of a small flat screwdriver press horizontally the plastic cover on its right side and remove it carefully.
To install a RCF mixing consoles Bluetooth card or a RCF mixing consoles player card, plug the 5 pin cable into the 5 pin connector on the PCB board as
shown.
To install a RCF mixing consoles player/recorder card, plug the 5 pin cable into the 5 pin connector and the 3 pin cable into the 3 pin connector on the
PCB board as shown.
Now place the optional card in its site and enjoy the new functions.
RCF mixing consoles BLUETOOTH CARD: Turn the Bluetooth interface on your mobile device on and press the PAIR button on the card. Your mobile device
will recognize the "BT2.1" Bluetooth device. Pair your device with the BT2.1 device. You can now play your favourite music.
Turn clockwise the knob named 2TK/MP3 up to 12 o'clock position and check if the TO MAIN MIX/TO CTRL ROOM switch is in upper position; now raise
carefully the MAIN MIX fader up to the desired listening level. You can adjust the volume on the card panel also pressing the buttons VOL+ and VOL‑.
RCF mixing consoles PLAYER CARD: from your computer, copy in a USB drive as many mp3 files as you want, even contained in folders (max 32 GB
total), insert the USB pen in the USB dedicated connector on the card, press and hold the PUSH&HOLD button for two seconds, the card will start to play
the first file of the first folder, the display will show alternatively the number of the file and the number of the folder which is playing. Press the " " or
" " button to skip to the previous or to the following track. Hold the same buttons pressed to change the selected folder. Use the PLAY/PAUSE button
to pause or restart playback. Press STOP to stop playback. Press the loop button ( ) repeatedly to select random play, loop the current track or loop the
entire programme, respectively.
Turn clockwise the knob named 2TK/MP3 up to 12 o'clock position and check if the TO MAIN MIX/TO CTRL ROOM switch is in upper position; now raise
carefully the MAIN MIX fader up to the desired listening level.
RCF mixing consoles PLAYER/RECORDER CARD: from your computer, copy in a USB drive as many mp3 files as you want, even contained in folders (max
32 GB total). Insert the USB flash drive in the dedicated USB port on the card, press and hold the PUSH & HOLD button pressed for two seconds. The card
will start playing the first file in the first folder. The file number and folder number which is playing will be shown on the display. Press the " " or " "
buttons to skip to the previous or to the following music file. Hold the same buttons pressed to change the selected folder. The card allows you to record
the program present on MAIN MIX: press the REC button once, now the board is in "rec ready status" and the display shows a flashing REC advise; press
REC again to start recording; press PUSH&HOLD button once for stop recording; the card will create a new folder on the USB pen called FrE01 where the
created files will find place. Use the PLAY/PAUSE button to pause or restart playback. Press the loop button ( ) repeatedly to select random play, loop the
current track or loop the entire programme, respectively.
Turn clockwise the knob named 2TK/MP3 up to 12 o'clock position and check if the TO MAIN MIX/TO CTRL ROOM switch is in upper position; now raise
carefully the MAIN MIX fader up to the desired listening level.
8
All manuals and user guides at all-guides.com
Gently remove the
plastic cover with the
help of a screwdriver.
3 pin connector
Be sure to
connect each
connector in its
proper position.
5 pin connector