Installation - Scheppach CSD4-4Li Instructions D'origine

misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment's potential hazards.
It is also imperative to observe the accident preven-
tion regulations in force in your area.
The same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
The machine may be used only with original acces-
sories and original tools of the manufacturer.
The safety-, workplace- and maintenance specifica-
tions of the manufacturer as well as the dimensions
specified in the technical data must be observed.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

10. Installation

m IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
Charging the battery pack
DANGER OF ELECTRIC SHOCK! Before cleaning
or servicing the charging station or the battery pack
always ensure that the plug is not in the mains sock-
et.
Note! A new battery pack, or one that has not been in
use for an extended period, must be charged
up before the first / renewed usage. The battery pack
attains its full capacity after ca. 3–5 charging cycles.
CAUTION! Always ensure the plug is removed from
the mains socket before inserting a battery pack
into, or removing one from, the charging station. Nev-
er charge the battery pack if the ambient tempera-
ture is less than 10 °C or greater than 40 °C.
Switch the charger off for at least 15 minutes be-
tween two successive charging procedures.
Remove the power plug from the wall socket.
22 | GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Changing tools
Your cordless electric drill / screwdriver has a fully
automatic spindle lock and is fitted with an
enclosed keyless chuck incorporating the latest tech-
nology .
Once the motor has come to a halt, the drive shaft is
automatically locked, so that the chuck 5 can
be opened simply by turning it . After you have in-
serted the required bit and fixed it in place by turning
the chuck , you can immediately continue working.
The spindle lock releases itself automatically when
the motor is started (by operation of the ON / OFF
switch 3 ).
Torque pre-selection
You can adjust the torque by using 6 torque prese-
lection. The torque levels regulate a range of up
to ca. 3,5 N m.
Select a low setting for small screws, soft workma-
terial.
Select a high setting for large screws, hard work ma-
terials and for the extraction of screws.
For drilling, push the selector to the setting for drill-
ing, in that you adjust the torque pre-selector
to the position .
For drilling tasks, also push the gear selector switch
1 to the front (Position: 2).
Handle adjustment
The screwdriver can be locked into 2 different
angle settings. To do so, press the locking
button (3) and move the screwdriver into the
desired position. Then release the locking
button (3).
_ Caution:
Before you switch on the screwdriver, make
sure that it is correctly locked in the required
angle position.
Preparing the tool for use
Switching On /Off
Switching on:
To start the appliance squeeze on the ON / OFF
switch 3 and then keep it pressed down. The LED
working light 4 comes on with a slightly or fully
pressed ON /OFF switch 3 and illuminates the work-
ing area in poor lighting conditions.
Switching off:
To stop the appliance, release the ON
Adjusting the speed
The ON / OFF switch 3 has a variable speed control
device. Slight pressure on the ON / OFF
switch 3 will cause the rotation speed to slow down.