Publicité
Les langues disponibles
Les langues disponibles
7
Electrical connection
- ELECTRICAL SAFETY :
Operate this machine only on a
supply equipped with a 30 mA
earthed current-limiting circuit-
breaker. Otherwise, consult our
catalogue for appropriate models.
- T h e R C C B m u s t b e u s e d
correctly, including testing it
regularly. For tools supplied
with an integral RCCB in the
cable or in the mains plug, if
t h e c a b l e o r p l u g h a s b e e n
d a m a g e d , r e p a i r s m u s t b e
c a r r i e d
o u t
m a n u f a c t u r e r , o n e o f h i s
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
- Make sure that the mains voltage
corresponds with that marked on
the manufacturer's plate on the
machine.
- Use the following types of plug,
single phase 2 P + E.
- Extension lead: Cable size
sufficient for the electrical power,
connection to the mains by a H07
RNF type cable of the following
size:3 x 2.5 mm
2
up to 50 m for
230 V
8
Starting
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches
from
machine.
Always keep blade guard in
place.
• To start the machine press the
green button on the switch [
3].
FIG.
• To stop the machine, press the
red button.
1-phase motor protected by a built-in
thermal circuit breaker.
To reset it, press the button.
9
Cutting method [
• Straight cuts :
• A reversible, removable side cutting
guide (A) can be used for 90° cuts
•
An extension
at the back of the side guide (A) using
screw
.
• Angled cuts :
•
An adjustable cutting guide (B) can be
used for cuts at an angle of 45° to 90°.
b y
t h e
Maintenance
10
be stopped)
• Clean the machine regularly.
Store in a dry place, not
accessible to children.
Maintain the tools carefully.
FAULT FINDING
In the event of faulty operation refer to the
tables below to find a solution.
• The machine does not work
CAUSES
Not plugged in
properly or cable
damaged
No mains voltage
Switch defective,
motor cable
floor
and
damaged
Motor faulty (no
power,
unpleasant smell)
SEE
• Difficult starting
CAUSES
Single phase
motor starting
condenser
11
Adjustments
• The machine is set before leaving the
factory and no adjustment is necessary.
4]
12
SEE FIG.
• Retighten the nuts and bolts periodically.
• In the event of a long period of use pay
special attention to the maintenance and
protection of the disc.
can be fixed in front or
• Tighten the disc correctly.
• Make sure that the contact faces of the
disc, the flanges and the spindle are
clean.
(the motor must
13
S
A
V
REMEDIES
- Make sure that
the supply is
14
correctly
plugged in
For rapid delivery of spares and in order to
(plug, extension
avoid any wasted time, it is necessary to
lead, etc)
remind your supplier of the details shown
- Check the
on the instruction plate on the machine with
supply cable
each order, as well as the reference of the
part to be replaced.
- Test or have
tested by an
electrician
(circuit breaker,
Item number
plug, etc)
- Have tested by
an electrician or
contact the
service
15
department
- Contact the
service
department to
have the motor
replaced
• Main materials :
REMEDIES
•
- Replace the
condenser
•
¤ Machine :
The instructions for use and spare parts found in
this document are for information only and are not
binding.
As part of our product quality improvement policy,
we reserve the right to make any and all technical
modifications without prior notice.
Important advice
The manufacturer declines all
responsibility for loss or damage
resulting from misuse or any
modification,
alteration
powering that does not conform
to the manufacturer's original
specifications.
At the work station, the sound
pressure level may exceed 85 db
(A)
In this case individual protection
measures must be taken.
Repairs
Contact your supplier who is
entirely at your service to carry
out repairs in the shortest time at
the best possible price.
Spare parts
00000000
(0)
Quantity
See exploded view
Scrapping
In the event of deterioration and
scrapping of the machine, the
following
items
must
disposed of in accordance with
the
requirements
of
legislation in force.
Motor : Aluminium (AL) - Steel (AC),
Motor :
Copper (CU)-Polyamide (PA)
Machine : Aluminium sheet (AL)
Steel (AC)
or
be
the
8
Publicité
