Husqvarna TS 300 D Manuel D'utilisation Et D'entretien page 12

This symbol indicates that the
machine is in conformance with
the applicable European directive.
SPECIAL INSTRUCTIONS
The disc cutter is designed to provide safe
and reliable service in operating conditions
corresponding with the instructions, but it
can present dangers for the user and risks
of damage, consequently regular on site
inspection is necessary to ensure :
• Perfect technical condition (use for the
purpose for which it is intended and
taking into account any risks, and
correction of
detrimental to safety).
• For dry cutting with a diamond disk
only. No other disk should be used
(abrasive, saw, etc).
• Competent personnel (qualifications,
age, training, education) who have
studied the manual in detail before
starting work: any fault of an electrical
or other nature must be checked by a
competent person
maintenance foreman, authorized
dealer, etc).
• That the warnings and instructions
marked on the machine are followed
(adequate personal protection, correct
use, general safety instructions, etc).
• That no modification, transformation or
addition is detrimental to safety and that
it is carried out without prior
authorization from the manufacturer.
• Respect of the maintenance intervals
and periodical checks recommended.
• That only genuine spare parts are used
for repairs.
Instruction plate
MANUFACTURER
TYPE TYPE
FABRICATION
WEIGHT MASSE UTILE K g
MAXI TOOL Ø MAXI OUTIL. m m
BORE Ø ALESAGE m m
SPEED T/MN - RPM
1 Use
Utilisation : Tile cutter
• Tools :
Dry diamond disks Ø
300xmm (D) -
bore 25.4 mm (AL).
(Information from your
usual supplier).
Use only continuous rim diamand
blades.
7
POWER
2.2 kW (3 CV)
2
• Motor speed : 2800 rpm
• Disc speed : 2800 rpm
• Electrical protection : IP 55
• Cutting height (E) : 75 mm
any malfunction
• Working width (A) : 420 mm
• Working width (B) : 250 mm
(electrician,
• Dimensions (l x w x h) (mm) :
• Weight : 23 kg
• Supply : 3 x 2.5
MOTOR
2,2 kW
N° SERIE SERIAL
FABRICATION
ANNEE DE
YEAR
PUISSANCE kW POWER
PLAGE DE
V VOLTAGE
TENSION
3
FREQUENCE Hz FREQUENCY
INT. UTIL. A INTENSITY
• On receiving the machine check its
condition.
• Always keep it perfectly clean
• Check the mains extension regularly.
• Always keep alert when working
• Check the mounting of the components
(abnormal vibration).
SEE FIG.
11 - Chassis
12 - Motor
13 - Switch - Mains connector
14 - Disk casing
15 - Side cutting guide
16 - Adjustable cutting guide
17 - Locking knob
18 - Side guide locking knob
19 - 30 mm spanner
10 - 13 mm spanner
VOLTAGE
CURRENT
± 5 %
230 V 50 HZ 14 A
Technical specifications
E
B A
640 x 500 x 375
2 H07-RNF cable
POWER PRESSURE VIBRATION
LEVEL LEVEL
EN ISO 3744 EN ISO 4871 G ENV 25349
80 Lw(A) 76 dB(A)
Inspection - Description of the
machine
1
4 Handling - transport
For dispatch or to prevent the guide moving
during transport, tighten the locking knobs
(8) [ 1].
SEE FIG.
5 Inspection before starting
Please read the instructions for
use prior to operating the
machine for the first time.
The use of ear protection is
mandatory.
The operator must wear
protective
appropriate to the work he
is doing. We recommend
that this includes both eye
and ear protection.
The working area must be
completely cleared, well lit and
all safety hazards removed (no
water or dangerous objects in
the vicinity).
Any persons not involved in the
work should leave the working
area.
Use blades suitable for the work
to be done (speed, geometry,
application, etc.).
LEVEL
0,1 G
6 Fitting the disc [
Disconnect the machine by
unplugging the supply cable.
• Loosen the nuts (A), then slide the cover
of casing (B) downwards and to the side.
• Unscrew the locking nut (C).
• Remove the locking plate (D).
• Lift the disk cover (E).
• Fit the disk (F).
• Replace the locking plate.
• Tighten the nut (C).
• Replace the casing cover (B).
• Tighten the nuts (A).
The disc locking nut has a left-
hand thread.
Take care about the direction of
rotation which is shown by an
arrow on one of the faces.
Make sure the contact faces of
flanges, of blade and the axle are
clean.
clothing
2]
SEE FIG.