Milwaukee CS60 Notice Originale page 20

Technical Data
Circular saw
Production code
Rated input
No-load speed
Saw blade dia. x hole dia
Max. Cutting depth at 90° / 45° / 56°
Saw blade thickness
Blade teeth
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) L
Sound power level (Uncertainty K=3dB(A)) L
Wear ear protectors!
GB
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Sawing of wood: Vibration emission value a
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN
62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different ap-
plications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
a) DANGER: Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary handle, or motor
housing. If both hands are holding the saw, they cannot be cut by the
blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below the
workpiece.
d) Never hold the workpiece in your hands or across your leg
while cutting. Secure the workpiece to a stable platform. It is
important to support the work properly to minimise body exposure, blade
binding, or loss of control.
English
18 18
pA
WA
h,W
e) Hold the power tool by insulated gripping surfaces only, when
performing an operation where the cutting tool may contact
hidden wiring or its own cord. Contact with a „live" wire will also make
exposed metal parts of the power tool „live" and could give the operator
an electric shock.
f) When ripping, always use a rip fence or straight edge guide.
This improves the accuracy of cut and reduces the chance of blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the mounting
hardware of the saw will run off-centre, causing loss of control.
h) Never use damaged or incorrect blade washers or bolt. The
blade washers and bolt were specially designed for your saw, for optimum
performance and safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, jammed or misaligned saw
blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator;
– when the blade is pinched or jammed tightly by the kerf closing down,
the blade stalls and the motor reaction drives the unit rapidly back toward
the operator;
– if the blade becomes twisted or misaligned in the cut, the teeth at the
back edge of the blade can dig into the top surface of the wood causing
the blade to climb out of the kerf and jump back toward the operator.
CS 60
4108 66 06 ...
4192 26 06 ...
... 000001-999999
1600 W
6300 min
-1
184 x 30 mm
61 / 49 / 35 mm
1,8 mm
24
4,8 kg
94,5 dB(A)
105,5 dB(A)
3,8 m/s
2
1,5 m/s
2