Siemens SITRANS F M MAGFLO Instructions page 7

® ® ® ® ®
SITRANS F M MAGFLO
Flange mating dimen-
sions (Metric)
Manufacturer's design
and safety statement
We have checked the contents of this manual for agreement with the hardware and
software described. Since deviations cannot be precluded entirely, we cannot guarantee
full agreement. However, the data in this manual are reviewed regularly and any
necessary corrections included in subsequent editions. Suggestions for improvement
are always welcomed.
Technical data subject to change without prior notice.
Siemens Flow Instruments A/S
Nordborgvej 81
DK-6430 Nordborg
Electromagnetic flowmeter type MAG 3100
Dimensions mm
mm OD PCD
PN 10
200 340 295
250 395 350
300 445 400
350 505 460
400 565 515
450 615 565
500 670 620
600 780 725
700 895 840
800 1015 950
900 1115 1050
1000 1230 1160
1200 1455 1380
PN 16
50 165 125
65 185 145
80 200 160
100 220 180
125 250 210
150 285 240
200 340 295
250 405 355
300 460 410
350 520 470
400 580 525
450 640 585
500 715 650
600 840 770
700 910 840
800 1025 950
900 1125 1050
1000 1255 1170
1200 1485 1390
PN 40
25 115 85
40 150 110
1. Responsibility for the choice of lining and electrode materials with regard to their abrasion
and corrosion resistance lies with the purchaser; the effect of any change in process medium
during the operating life of the flowmeter should be taken into account. Incorrect selection
of lining and/or electrode materials could lead to a failure of the flowmeter.
2. Stresses and loading caused by earthquakes, traffic, high winds and fire damage not taken
into account during flowmeter design.
3. Do not install flowmeter such that it acts as a focus for pipeline stresses. External loadings
not taken into account during flowmeter design.
4. During operation do not exceed the pressure and/or temperature ratings indicated on the
data label or in the installation instructions.
5. It is recommended that all installations should include an appropriate safety valve and
adequate means for draining/venting.
6. Under the Pressure Equipment Directive this product is a pressure accessory, and not
approved for use as a safety accessory, as defined by the Pressure Equipment Directive.
7. Removal of the terminal box except by Siemens Flow Instruments or their approved agents
will invalidate the PED conformity of the product.
In accordance with the Pressure Equipment Directive (97/23/EC)
Bolting
T B Holes Bolts
24 22 8 M20
26 22 12 M20
26 22 12 M20
28 22 16 M20
32 26 16 M24
36 26 20 M24
38 26 20 M24
42 30 20 M27
30 30 24 M27
32 33 24 M30
34 33 28 M30
34 36 28 M33
38 39 32 M36
19 18 4 M16
20 18 8 M16
20 18 8 M16
22 18 8 M16
22 18 8 M16
24 22 8 M20
26 22 12 M20
29 26 12 M24
32 26 12 M24
35 26 16 M24
38 30 16 M27
42 30 20 M27
46 33 20 M30
52 36 20 M33
36 36 24 M33
38 39 24 M36
40 39 28 M36
42 42 28 M39
48 48 32 M45
16 14 4 M12
18 18 4 M16
The reproduction, transmission or use of this document or its contents is not permitted without
express written authority.
Offenders will be liable for damages. All rights, including rights created by patent grant or
registration of a utility model or design, are reserved.
Copyright © Siemens AG 04.2005 All Rights Reserved
Order no.: FDK-521H0970-02
Printed in: Denmark
Dimensions mm
mm OD PCD T
150 lb
25 108 79 14
40 127 98 18
50 152 121 19
65 178 140 22
80 190 152 24
100 229 191 24
125 254 216 24
150 279 241 25
200 343 298 29
250 406 362 30
300 483 432 32
350 533 476 35
400 597 540 36.5
450 635 578 40
500 699 635 43
600 813 749 48
AWWA
700 927 864 33
750 984 914 35
800 1060 978 38
900 1168 1086 41
1000 1289 1200 41
1050 1346 1257 44
1200 1511 1422 48
Bolting
B Holes Bolts
16 4 M14
16 4 M14
19 4 M16
19 4 M16
19 4 M16
19 8 M16
22 8 M20
22 8 M20
22 8 M20
25 12 M24
25 12 M24
28 12 M27
28 16 M27
32 16 M30
32 20 M30
35 20 M33
35 28 M33
35 28 M33
41 28 M39
41 32 M39
41 36 M39
41 36 M39
41 44 M39
7