Table Des Matières - Unitec MAB 825 Mode D'emploi

Table of Contents
Foreword . . . . . . . . . . . . . . . . . . . . . . . .34
Instructions for use . . . . . . . . . . . . . . .34
Copyright . . . . . . . . . . . . . . . . . . . . . . . .34
Structure of the safety warnings . . . . . . .35
Intended use . . . . . . . . . . . . . . . . . . . . . .36
Liability disclaimer . . . . . . . . . . . . . . . . .36
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Fundamental safety precautions . . . . . .37
Electric shock hazard . . . . . . . . . . . . . . .38
Risk of injury . . . . . . . . . . . . . . . . . . . . . .39
Prevention of damage . . . . . . . . . . . . . .40
Safety installations . . . . . . . . . . . . . . . . .41
Personal protective equipment . . . . . . . .42
Components/scope of supply . . . . . . .43
Machine overview . . . . . . . . . . . . . . . . . .43
Delivery contents . . . . . . . . . . . . . . . . . .44
Control panel . . . . . . . . . . . . . . . . . . . . .44
Before using for the first time . . . . . . .45
Transport inspection . . . . . . . . . . . . . . . .45
Preparations . . . . . . . . . . . . . . . . . . . . .45
Additional safety measures for
certain operations . . . . . . . . . . . . . . . . . .45
Check the condition of the substrate . . .46
Inserting the tool . . . . . . . . . . . . . . . . . . .47
MAB 825/845
Operation . . . . . . . . . . . . . . . . . . . . . . .51
Activating/deactivating magnetic clamp . .51
Switching machine ON/OFF . . . . . . . . . .52
Selecting the speed range . . . . . . . . . . .52
Setting the speed . . . . . . . . . . . . . . . . . .53
Setting the torque cut-out . . . . . . . . . . . .53
Rotating mechanism (MAB 845 only) . . .54
Drilling with the machine . . . . . . . . . . . .54
Thread cutting . . . . . . . . . . . . . . . . . . . .56
Reaming/counter-sinking . . . . . . . . . . . .56
Eliminating blockages . . . . . . . . . . . . .57
Cleaning . . . . . . . . . . . . . . . . . . . . . . . .57
After every use . . . . . . . . . . . . . . . . . . . .57
Maintenance . . . . . . . . . . . . . . . . . . . . .58
Adjusting the guide of the machine slide . .58
Replacing the carbon brushes . . . . . . . .58
After-Sales Service/Service . . . . . . . . . .58
Troubleshooting . . . . . . . . . . . . . . . . . .59
Faults - causes and remedies . . . . . . . .59
Storage/disposal . . . . . . . . . . . . . . . . .60
Storage . . . . . . . . . . . . . . . . . . . . . . . . . .60
Disposal . . . . . . . . . . . . . . . . . . . . . . . . .60
Annex . . . . . . . . . . . . . . . . . . . . . . . . . .61
Technical data . . . . . . . . . . . . . . . . . . . .61
EC Declaration of Conformity . . . . . . . . .62
33