Kuppersbusch EWK880-0-2Z Mode D'emploi page 23

Maintenance / Problems and solutions
You can solve many standard problems yourself without needing to call Customer Service. Try the suggestions below:
PROBLEM
Appliance does not operate
Appliance is not cold enough
Appliance turns itself on and off
frequently
The light does not work.
Vibrations
The appliance seems to make
too much noise
The door will not close properly
Display "E0", "E1". "E2", "E3",
"E4", "E5", "E6" or "E7"
The alarm sounds
The icon "--" is lit up and flashing
in the temperature display.
POSSIBLE CAUSE
Appliance is not connected to a power supply.
The appliance is turned off.
Circuit breaker has tripped or a fuse has blown.
The temperature is not set correctly.
The ambient temperature could require a different
temperature setting.
The door was opened too often.
The door was not closed completely.
Door is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or too dusty.
The room temperature is higher than average.
A large amount of bottles has been added to the unit.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Appliance is not connected to a power supply.
Circuit breaker has tripped or a fuse has blown.
The light was switched off on the control panel.
The appliance is not properly level.
The rattling noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear
gurgling sounds caused by the flow of refrigerant in your appliance.
If temperature fluctuations occur, the contraction and expansion of the inner walls may cause popping and crackling
noises.
The appliance is not properly level.
The appliance is not properly level.
The door was reversed and not properly re-installed.
The gasket is dirty.
The shelves are out of position.
"E0" indicates a communication error for 3 zone models.
"E1" or "E2" indicates that the air temperature sensor
has failed.
"E3" or "E4" indicates that the defrost sensor in the
evaporator has failed.
"E5" indicates a defrost heater failure.
"E6" indicates a solenoid valve failure.
"E7" indicates a door switch failure.
Has the appliance door been open for longer than 60
seconds? If not, then the temperature has risen higher
or fallen lower than the temperature that has been set.
This could be due to:
• The appliance door being opened too often.
• The ventilation opening being covered or too dusty.
• A lengthy interruption to the power supply.
• A large amount of bottles has been added to the unit.
The temperature display is out of the range.
REMEDY
Connect the appliance.
Switch on the appliance.
Switch on circuit breaker or replace fuse.
Check the set temperature.
Set a different temperature.
Do not open the door more often than necessary.
Close door properly.
Check the door seal and clean or replace.
Clean the condenser when necessary.
Clear the obstructions and clean off the dust.
Put the appliance in a cooler place.
Leave the appliance to work for a while until the set
temperature has been reached.
Do not open the door more often than necessary.
Close door properly.
Check the door seal and clean or replace.
Connect the appliance.
Switch on circuit breaker or replace fuse.
Switch on the light.
Level the appliance with the adjustable feet.
Level the appliance with the adjustable feet.
Level the appliance with the adjustable feet.
Check the door hinge and reassemble correctly.
Clean the door gasket.
Check the shelves and refit correctly.
Call for service.
If yes, close the door.
• Do not open the door more often than necessary.
• Clear the obstructions and clean the dust.
• Leave the appliance to work for a while until the set
temperature has been reached.
Only temperatures within the display range 16~99°F/-
9~37°C can be shown. If the temperature is not within
this range, the icon "--" will be displayed instead. That is
normal.
EN
23