Publicité
Les langues disponibles
Les langues disponibles
Pressure Washers
Operation (Continued)
1. Before triggering the gun, adjust the
nozzle or quick connect tip to a wide
fan pattern.
2. Place the nozzle approximately 4-5
feet away from the cleaning surface.
Then hold the nozzle at a 45 degree
angle to the cleaning surface. Trigger
the gun.
3. Vary the fan pattern spray angle and
the distance to the cleaning surface
until optimum cleaning efficiency is
achieved without damaging the sur-
face.
TURBO NOZZLE (NOT INCLUDED WITH
ALL MODELS)
A turbo nozzle, sometimes referred to as
a rotary nozzle, can significantly reduce
cleaning time. The turbo nozzle combines
the power of a narrow high impact
stream with the efficiency of a 25 degree
fan pattern. The turbo nozzle swirls a nar-
row high impact stream into a cone
shape to clean a larger area.
Since a turbo nozzle
NOTICE
uses a narrow high
impact stream, only use a turbo lance in
applications where the cleaning surface
cannot be damaged by narrow high
impact spray. The turbo nozzle is NOT
adjustable and cannot be used to apply
detergent.
4. Detergent Application
USE THE INSTRUCTIONS APPROPRIATE
FOR MODEL PURCHASED
NOTE: Use only detergents formulated
for pressure washers.
NOTE: Test detergent in an inconspicuous
area before use.
Never slide the
NOTICE
nozzle from low to
high pressure or from high to low pres-
sure when the gun is triggered.
Never replace quick
WARNING
!
connect tip when gun
is triggered.
DETERGENTS
The use of detergents can dramatically
reduce cleaning time and assist in the
removal of difficult stains. Many deter-
gents are customized for pressure washer
use on specific cleaning tasks. Pressure
washer detergents are as thick as water.
Using thicker detergents – like dish soap –
will clog the chemical injection system
www.chpower.com
and prevent the application of the deter-
gent.
Once applied to a cleaning surface, deter-
gents take time to break down dirt and
grime. Detergents work best when
applied at low pressure.
You can effectively clean surfaces by com-
bining the chemical action of detergents
with high pressure rinses. On vertical sur-
faces, apply the detergent starting at the
bottom and work your way upward. This
method prevents the detergent from slid-
ing down and causing streaks. Begin high
pressure rinsing at the bottom and work
your way upward. On particularly tough
stains, use a brush in combination with
detergents and high pressure rinsing.
1. Follow manufacturer's label direc-
tions for mixing correct concentra-
tions of soap/detergents. The soap
detergent to water ratio through
the pump is approximately 10% (1
to 10).
2. Insert the filter end of the clear plas-
tic detergent tube into the deter-
gent container.
3a. Place hand around the 3.5" spraying
end section of the lance (the section
Figure 16 - Quick Connect Tip
Low Pressure
Figure 18 - Adjusting nozzle for pressure
8
that turns from left to right). Pull
firmly and quickly away from you.
(NOTE: Do not adjust lance while
spraying.) The lance will extend
1/2" and be in low pressure (See
Figure 18). Soap can only be drawn
in low pressure.
3b. For units with quick connect tips:
use the black 65
spray tip (See Figure 16).
4. If equipped, adjust the detergent
injection flow by turning the collar
of the injector. Turning collar clock-
wise decreases flow of detergent
and turning collar counter clock-
wise increases detergent flow (See
Figure 17).
Figure 17 - Detergent injection adjust-
ment
GENERAL CLEANING TIPS
1. Apply the detergent so that it thor-
oughly covers the cleaning surface.
Apply the detergent from bottom to
top to prevent the detergent from
High Pressure
o
quick connect
Nozzle
Publicité
