Nilfisk Advance Pacesetter 13 Mode D'emploi page 6

EN
ENGLISH
TROUBLESHOOTING
SWIRLS ON THE FLOOR AFTER SCRUBBING
• Floor not clean.
• Incorrect solution.
• Area not properly swept - debris in pad or brush.
• Improper pad or brush for the job.
• Moving the machine too fast.
SWIRLS ON THE FLOOR AFTER DRY BUFFING
• Moving the machine too fast.
• Floor fi nish too soft.
• Area not properly swept - debris in pad or brush.
• Improper pad or brush for the job.
CIRCLES ON THE FLOOR
• Machine standing still while the brush or pad is running.
FLOOR FINISH REMOVED
• Improper pad... too aggressive.
• Solution too strong.
MACHINE WOBBLES DURING OPERATION
• Defective pad... one side is more dense than the other.
• Machine left sitting on brush or pad for extended period of time causing bristles or pad to "take a set".
• Pad not "seated" properly into pad holder bristles.
• Warped block on brush or padholder - replace.
MACHINE DOES NOT RUN
• Check plug for proper connection - on machine and at wall outlet.
• Check building circuit breaker.
• Call for service.
TECHNICAL SPECIFICATIONS FOR 120V MACHINES (as installed and tested on the unit)
Model
Model Number
Motor
Transmission
Clutch Plate
Pad/Brush Speed
Pad/Brush Size
Wheels
Cord Length
Height w/Handle
Weight (w/cord)
Construction:
Handle Tube
Base
Model
Model Number
Motor
Transmission
Clutch Plate
Pad/Brush Speed
Pad/Brush Size
Wheels
Cord Length
Height w/Handle
Weight (w/cord)
Construction:
Handle Tube
Base
6 - FORM NO. 70139A - Pacesetter 13, 17, 20, 17HD, 20HD, 20TS, 20SD
Pacesetter™ 13 Pacesetter™ 17
01282A 01290A
1 hp, 120V/60Hz 1 hp, 120V/60Hz
Two-Planetary Two-Planetary
NP-92
175 rpm 175 rpm
13" (33 cm) 17" (43 cm)
5" (13 cm) 5" (13 cm)
50' (15 m) 50' (15 m)
46" (117 cm) 46" (117 cm)
81 lbs. (36.8 kg) 83 lbs (37.7 kg)
Tubular Steel Tubular Steel
Die-Cast Aluminum Die-Cast Aluminum
Pacesetter™ 17HD Pacesetter™ 20HD
01330A / 56383336 01410A / 56383337
1.5 hp, 120V/60Hz 1.5 hp, 120V/60Hz
Triple-Planetary Triple-Planetary
NP-92
175 rpm 175 rpm
17" (43 cm) 20" (51 cm)
5" (13 cm) 5" (13 cm)
50' (15 m) 50' (15 m)
46" (117 cm) 46" (117 cm)
91 lbs (41.1 kg) 95 lbs (43.2 kg)
Tubular Steel Tubular Steel
Die-Cast Aluminum Die-Cast Aluminum
Pacesetter™ 20
01370A
1 hp, 120V/60Hz
Two-Planetary
NP-92 NP-92
175 rpm
20" (51 cm)
5" (13 cm)
50' (15 m)
46" (117 cm)
87 lbs (39.5 kg)
Tubular Steel
Die-Cast Aluminum
Pacesetter™ 20TS
01440A
0.9/1.5 hp, 120V/60Hz
Triple-Planetary
NP-92 NP-92
180/320 rpm
20" (51 cm)
5" (13 cm)
50' (15 m)
46" (117 cm)
81 lbs (36.8 kg)
Tubular Steel
Die-Cast Aluminum
Pacesetter™ 20SD
01460A
1.75 hp, 120V/60Hz
Triple-Planetary
NP-92
175 rpm
20" (51 cm)
5" (13 cm)
50' (15 m)
46" (117 cm)
102 lbs (46 kg)
Tubular Steel
Die-Cast Aluminum
revised 3/13