Publicité
Les langues disponibles
Les langues disponibles
Installation Instructions Ergon GX1 Grips
Attention: Please read these instructions carefully. Only correctly installed Ergon grips allow for optimum function. Ergon GX1 grips require a handlebar with 132 mm of straight uninterrupted
!
bar space each side. Only handlebars with 22.2 mm diameter in the grip area may be used. Only handlebars that have been approved by their manufacturer for use with clamp on grips should
be used and can withstand the required clamping force. Carbon bar use permitted. Thin wall handlebars (some carbon and aluminium models) can be used. Please ensure prior to fi tting that
the bar is suitably cleaned using alcohol or other degreasers. These grips are not designed to be used with twist shifters.
1.
The grips are left and right specifi c, please
ensure that they correctly orientated.
3.
Turn the grip so that the support platform completely supports the ball of your hand. The wrist should be in a neutral position
avoiding an exaggerated kink. After a short period of trial and error a comfortable position can be found. Be sure to tighten
the clamp with 5 Nm before your fi rst ride.
5.
Important:
Recommended torque: 5 Nm
The grips should not turn on the bar!
Re-check the torque setting following the fi rst ride /
50km of riding. Check periodically to ensure that the
screws are not loosening.
Tighten to 5 Nm torque using a 3 mm torque wrench. Re-check the torque setting following the
fi rst ride / 50 km of riding. Check periodically to ensure that the screws are not loosening.
!
Attention:
Before riding the bike, please ensure that the grips are properly tightened. If the quoted 5 Nm torque is not suffi cient to
prevent the grips being turned by hand then the handlebar is not compatible with this product. Please replace the handlebar
with one which is completely round at the end and meets the industry standard of 22.2 mm in diameter. Do not over-tighten.
To prevent corrosion, the clamp has a protective coating. Should this coating become damaged, from a crash for example,
it is advisable renew this layer using a paint pen or similar. Following any accidents, all components of the grips and clamps
should be checked for damage and replaced as necessary. Should you have any questions, please refer to your retailer.
Before riding for the fi rst time, ensure that the function of the brakes and gears has not been restricted without having to
change your hand position and that all functions of the bicycle can be used as normal. A secure fi t can only be guarantied
with the use of the correct Ergon clamp and spacer.
Maintenance:
In order to ensure that your Ergon grips provide you with the best performance please clean them regularly using warm
soapy water. Rinse thoroughly. Do not use petroleum based products or solvents, oil or grease on the grips for any reason.
Warranty:
The clamping system used on these grips exceeds the DIN standard 14766 for handlegrips of 70 Nm removal force. The
function and construction of Ergon handlebar grips are covered by a warranty for two years from the date of purchase.
Please be aware that grips do naturally wear out with use. In the event of a suspected warranty issue, please contact
your retailer. Damage as a result of crashes, misuse, incorrect installation or modifi cation of the grip is not covered by this
warranty.
2.1
2.2
Fit the alu spacer and the clamp
Slide the grip onto the handlebar.
over the grip. Ensure that a good
contact has been made.
2.3
Ensure that the grip is fully
inserted onto the bar so that it is
fl ush with the end of the bar.
4.
The default position for the support platform is horizontal. For fi ne tuning
according to rider and riding style, please refer to the step 3 and the tips
given below.
6.
Important:
Check List!
Please ensure that you have the correct grips mounted left and right (1). The end of the clamp
should be level with the end of the bar (2.3). Insert the end plugs as shown.
( GB / US )
2.4
Tighten the clamp using the
upward facing screws.
-15° to +25°
Information:
Ergon grips offer pain prevention through
optimized pressure distribution. This is realised
through the 40% larger surface area. This
pressure distribution allows better blood
circulation, which may cause the hands to
appear fl ushed.
The correct position for your Ergon grips is
an individual thing. Repeat steps (3) to (5)
adjusting the angle of the grips in small steps.
The angle maybe different for the left and
right hand. Ride a test course to allow good
comparison.
Should you suffer from pain or numbness in
your hands or forearms despite use of Ergon
grips it may help to try a handlebar with a
different profi le, or rotate your existing one.
If problems persist, it is advisable to check
your position on the bike including frame size,
handlebar height and saddle position with the
help of a professional.
Allergy information:
All Ergon grips are latex free.
Publicité
